Publicité
English
7. Install the chain, guide bar and sprocket cover
described in Installing the Guide Bar and Saw Chain,
Replacing the Saw Chain sections and adjust chain tension
properly before use as described in the Adjusting Chain
Tension section.
Accessories
WARNING: Since accessories, other than those offered by
D
WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous. To reduce the
risk of injury, only D
WALT recommended accessories should
e
be used with this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
WARNING: The use of accessories not recommended in
this manual may be hazardous.
Replacement chain and bar are available from your nearest
D
WALT authorized service center. For use only with low
e
kick back bar and chain.
Available bars and chains for DCCs621:
Bar: DWZCSB12, service part number NA599492.
Chain: DWO1DT612, service part number N580237.
Saw Chain Sharpening (Fig. O–Q)
CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can cut you
when it is not running.
WARNING: Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool before
performing the following operations. Failure to do this could
result in serious personal injury.
WARNING: Do not over file chain rakers, this will increase
the risk of kickback. If the chain has been sharpened more
than four times, replace it.
Each time the chain is sharpened, it loses some of the low
kickback qualities and extra caution should be used.
It is recommended that a saw chain be sharpened no
more than four times.
nOTE: The cutters will dull immediately if they touch the
ground/dirt or a nail while cutting.
To get the best possible performance from your chainsaw
it is important to keep the teeth of the saw chain sharp.
Follow these helpful tips for proper saw chain sharpening:
1. For best results use a 5/32" (4 mm) file and a file holder
or filing guide to sharpen your saw chain. This will ensure
you always get the correct sharpening angles.
2. Place the file holder flat on the top plate and depth
gauge of the cutter.
3. Keep the correct top plate
on your file guide parallel with your chain (file at 60 ° from
chain viewed from the side) as shown in Fig. O.
4. Sharpen cutters on one side of the chain first. File from
the inside of each cutter to the outside. Then turn your saw
around and repeat the processes (2, 3, 4) for cutters on the
other side of the chain.
nOTE: Use a flat file to file the tops of the rakers (portion of
12
6
as
WALT Industrial
e
23
filing angle line of 30 °
chain link in front of the cutter) so they are about .025" (.635
mm) below the tips of the cutters as shown in Fig. P.
5. Keep all cutter lengths equal as shown in Fig. Q.
6. If damage is present on the chrome surface of the top
plates or side plates, file back until such damage is removed.
CAUTION: After filing, the cutter will be sharp, use extra
caution during this process.
Tool Connect™ Chip (Fig. R)
WARNING: To reduce the risk of serious personal
injury, turn unit off, set the brake and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start‑up can cause injury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
the screws.
4. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should be
performed by a factory service center or an authorized service
center. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration of
ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/account-login.
24
that hold the Tool
into the tool.
25
26
.
Publicité
