Technical Data - Milwaukee 2205-40 Notice Originale

TECHNICAL DATA

Dial Position Range
Current AC 200 A
400 V
Voltage AC/DC
1000 V
400 Ω
4 kΩ
Resistance
40 kΩ
400 kΩ
Continuity
4 MΩ
40 MΩ
400.0 V
Low Input Impedance
1000 V
Accuracy is specified for 1 year after calibration, at operating temperatures of 18°C to 28°C, with relative humidity
at 0 % to 85%.
Maximum voltage between any terminal and earth ground
CAT III
CAT IV
Jaw Opening (maximum conductor size)
Temperature Operating
Temperature Storage
Temperature Coefficient
Operating Altitude
Battery run time
Battery
Weight according EPTA-Procedure 01/2003
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS Measuring Instrument
Never make measurement on a circuit in which voltage over
1000 V exists. Use only leads rated 1000 V or better.
Disconnect the test leads from the instrument for current
measurement.
Keep fingers away from jaws during measurements.
To reduce the risk of electric shock for Resistance, Continuity,
and Capacitance measurements, never use the meter on an
energized circuit. Make sure a capacitor is fully discharged
before touching or attempting to make a measurement.
Do not attempt to make measurement in the presence of
flammablegasses. Otherwise, the use of the instrument may
cause sparking, which can lead to an explosion.
Never attempt to use the instrument if its surface or your hand
is wet.
Do not exceed the maximum allowable input of any measuring
range.
Only test on unenergized circuits unless absolutely necessary.
Check tool functionality on a known circuit first.Never
assume tool is working. Assume circuits are live until they
can be proven de-energized.
Do not ground yourself while measuring. Avoid body contact
with earthed or grounded sur-faces such as pipes, radiators,
ranges and refrigerators.
Never remove the case or battery cover during a measurement.
This instrument is to be used only in its intended applications or
conditions. Otherwise, the instrument's safety functions may
not work, resulting in serious personal injury and instrument
damage.
22 ENGLISH
Resolution Accuracy
0.1 A ±(3.0% +3dgt) 45-60Hz
:±(1.5% +5dgt) 45-500Hz
0.1 V / 1 V
: ±(1.0% + 2dgt)
0.1 Ω ±(1% +5dgt)
0.001 kΩ ±(1% +2dgt)
0.01 kΩ ±(1% +2dgt)
0.1 kΩ ±(1% +2dgt)
0.001 MΩ ±(1% +2dgt)
0.01 MΩ ±(2% +5dgt)
0.1 V / 1 V ±(2.0% + 3dgt) AC: 45-500Hz
1000 V
600 V
16 mm
-10°C - 50°C
-40°C - 60°C
0,1 x specified accuracy /°C (<18°C or >28°C)
2000 m
approx. 26 h with all functions
2 AA
275 g
To reduce the risk of injury from shock and arc blasts, always
wear personal protective equipment where live conductors are
exposed.
Never attempt to make measurement if any abnormal
conditions, such as broken case and exposed metal parts are
found on the instrument.
Do not rotate the Rotary Dial while the test leads are being
connected.
Do not install substitute parts or make any modification to the
instrument. For repair or re-calibration, return the tool to a
factory Service/Sales Support Branch or authorized service
station.
Only use Milwaukee test leads with the Milwaukee Clamp
Meters.Inspect test leads before each use. Use clamp meter to
run a continuity test.
Non-Contact Voltage Detection (NCVD):
The LED may not be displayed due to installation condition of
electrical circuit or equipment. Never touch the circuit under
test to avoid possible danger even if the LED for NCVD is not
displayed. Check the functionality of LED on a well-known
power supply prior to measurement. When the LED doesn't
light up, do not make measurement. NCVD indication is
affected by external voltage, and how the meter is held or
placed.
Measurement categories and their significance according
to IEC 61010-1:
CAT III: Measurements in the building installation: stationary
loads, distribution board, device firmly on the distribution board.
CAT IV: Measurements at the source of low voltage: counter
main supply, primary overcurrent.
For your present measuring instrument is valid the measuring
category and associated maximum rated voltage,
eg. 600 V CAT III, which are printed on the device.
SAFETY INSTRUCTIONS Battery
This tool is designed to be powered by 2 AA batteries
properly inserted into the instrument. Do not attempt to use
with any other voltage or power supply.
Do not leave batteries within the reach of children.
Do not mix new and used batteries. Do not mix brands (or
types within brands) of batteries.
Do not mix rechargeable and non-recharge-able batteries.
Install batteries according to polarity (+ / –) diagrams.
Properly dispose of used batteries immediately.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
This appliance is not intended for use by persons (including
children) with limited physical, sensory or mental capabilities or
insufficient experience and/or knowledge unless they are
supervised by a person who is responsible for their safety or
have been instructed by them in the safe use of the tool.
Children should be supervised in order to ensure that they do
not play with the tool.
SPECIFIED CONDITIONS OF USE
The Measuring Instrument can be used for following
measurements: Current AC, Voltage AC, Voltage DC,
Resistance, Continuity, Capacitance, Temperature, Voltage
AC and DC at low input inpedance of the measurung
instrument,. This instrument may only use for measuring the
previously indicated measurements.
SLEEP FUNCTION
This instrument is automatically powered off in about 20 min
after the last Rotary Dial or button operation. To reset, rotate
the Rotary Dial or press a button.
WORKING TIPS
Set the Rotary Dial to an appropriate position before starting
measurement.
Firmly insert the test leads.
Disconnect the test leads from the instrument for current
measurement.
Do not expose the instrument to the direct sun, high
temperature and humidity or dew fall.
Altitude 2000 m or less. Appropriate operating temperature is
within -10ºC and 50ºC.
This instrument isn't dust & water proofed. Keep away from
dust and water.
Be sure to power off the instrument after use. When the
instrument will not be in use for a long period, place it in
storage after removing the battery.
Use a damp cloth or neutral detergent for cleaning the
instrument. Do not use abrasives or solvents.
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or
directly at: Milwaukee Electric Tool, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste
electrical and electronic equipment and its
implementation in accordance with national
law, electric tools that have reached the end
of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
WARNING
To avoid electrical shock remove test leads
before opening case or removing battery
pack/ battery.
Ground
Double isolated
Never make measurement on a circuit in
>1000 V
which voltage over 1000V exists.
Keep fingers away from test tips during
measurements.
ENGLISH 23