Publicité
OPTION SELECTIONS
OPTIONS
CAN BE
WHAT IT DOES
ADDED TIME TO CYCLE
ADDED
SELECTED WITH
WATER
GALLONS
TYPICAL
MAX
(LITERS)
Control Lock
Avoids unintended use of the dishwasher between cycles, or cycle and option changes during a cycle.
To turn on Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The Control
........
Lock light will stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any button
or
while your dishwasher is locked, the light flashes 3 times and an audible tone will sound. The dishwasher door can still
be opened/closed
while the controls are locked.
To turn off Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The light
...... ,.........
turns off.
NOTE: If your model requires you to press and hold 4 Hour Delay to lock the controls, the Control Locked LED will be
on or off to indicate if the Control Lock is active or not.
CONTROL
PURPOSE
COMMENTS
To
Start or iesume a
If the d0or is Opened during a cYcle Oi the p0Wer is interiUpted, the START/RESUME
wash
cYCle
indicator flashe& The cyc!e wi!l not resume until the doo r is C!°sed and START/RESUME is
,_0oo,o,,c,_._
pressed.
NOTE" If the START/RESUME button iS located On top of door, pUsh door firmly CloSed
within 3 seconds of pressing START/RESUME. If the door is not closed within 3 seconds,
the start button LED wi!! flash, an audible tone wi!! be heard, and the cyc!e wi!! not start,
To reset any cycle or
options during
selection.
To cancel a wash
cycle after it's
started.
Press CANCEL/DRAIN to reset any control selections made.
See "Canceling A Cycle After Dishwasher Is Started" and "Changing a Cycle After
Dishwasher is Started" sections.
To turn the audible
Press and hold the Hi Temp sCrub button for 3 Seconds to turn the aUdible tones on or 0ft.
tones on or off.
Only audible tones for confirming button presses can be turned on/off. Important audible
_or, oo_o,:,o_
tones, such as indicating a cYCle has been interrupted,
cannot be deactivated.
CONTROL
PURPOSE
COMMENTS
wl;,::_,._ _i;_:ii_::i
The cYcle Status Indicator
Clean indicatoi glows When a CYc!e is finished.
L ghts are used to fo ow the
i
......
if Y0U select the sani Rinse opti0n; When the san! Rinse cycle is finished,
progress of tne a_snwasner
. ;
{ ,t
,"
_. : theSanitizedindicat°rg!°ws'lfy°urdishwasherdidn°tpr°perlysanitize
cyc e Locatecl on ire front
of t'e dishwaS"e
for f
t
your dishes, the light flashes at the end of the cyc!e. This can happen if the
n
n
r
ton
.
;
,
,
,;
.
,
cycle is interrupted, orthe water could not be heated to the required
con[ro moaes
ann ocatea
tem-erature
....
on the top of the door for
p
:
hidden control models.
The Clean and Sanitized lights go Off when you open and close the door or
press CANCEL
The Front Indicator Light or
Single Exterior Light (A)
shows progress of your
dishwasher cycle by color
(for hidden control models
only).
The light will be blue if the dishwasher is washing or rinsing. The light will
be red when the dishwasher
is drying. The light will be green to indicate
that the cycle is complete. If the Front Indicator Light is blinking, see
"Troubleshooting"
section.
The Cycle Status DisplaY is
The indicators wi!! inform you if you are ab!e to add a dish to the cycle afte i
used to follow the progress
it has started. It will a!so inform you if the dishwasher is washing, rinsing,
of the dishwasher cycle, and
drying, complete,
and/or sanitized. They will show whether the control is
to show other information,
locked and!or the delay option is se!ected. A series of bars wil! count down
(Available
on some mode s
the duration of the cycle remaining from left to right. Each bar equals
instead of Cycle Status
approximately 24 minutes of cycle lengthl The bars wi!l also count down
Indicator Lights)
the delay feature from left to right, and the delay indicator will be activated.
10
Publicité
