Publicité
Helping to minimise your vibration and noise exposure
risk.
Always use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions
and keep well lubricated (where appropriate).
If the tool is to be used regularly then invest in anti
vibration and noise accessories.
Plan your work schedule to spread any high vibration tool
use across a number of days.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
INTENDED USE
The machine is intended for driving in and loosening
screws as well as for drilling in wood, metal and plastic.
ASSEMBLY AND OPERATION
ACTION
BEFORE OPERATION
Removing the battery pack
10
Charging the battery pack
Installing the battery pack
ASSEMBLY
CHUCK ADJUSTMENT
WARNING: Always lock off trigger switch and
disconnect tool from power source when changing
accessories. Always ensure the bit is secure before starting
the tool. Damage to the Chuck or a loose bit may cause
possible personal injury.
--Removing the bits
--Inserting the bits
OPERATION
FORWARD/REVERSE ROTATION
CONTROL
WARNING: Never change the direction
of rotation when the chuck is rotating,
wait until it has stopped!
TWO-SPEED GEAR CONTROL
TORQUE ADJUSTMENT
SCREWDRIVING, DRILLING, HAMMER
DRILLING
Cordless hammer drill
OPERATING THE ON/OFF SWITCH
WARNING: Do not operate
for long periods at low speed
because excess heat will be produced
internally.
LED LIGHT INDICATOR (See Fig. F)
To turn on the light, press the on/off switch and make sure
the forward/reverse rotation control is on right/left position.
When you release the on/off switch, the light will be off.
LED lighting increases visibility-great for dark or enclosed
area. LED is also a battery capacity indicator. It will flash
when power gets low.
The tool and battery pack are equipped with a protection
system. When the LED Light is quickly flashing and turn off,
the system will automatically cut off power to the tool to
extend battery life. The tool will automatically stop during
operation if the tool and/or battery pack are placed under
one of the following conditions:
• Overloaded: The tool is operated in a manner that
causes it to draw an abnormally high current. In this
situation, release the Trigger Switch on the tool and stop the
application that caused the tool to become overloaded. Then
pull the Trigger Switch again to restart.
• Overheated: Under the condition above, if the tool does
FIGURE
not start, the Tool and Battery Pack are overheated. In this
situation, let the Tool and Battery Pack cool before pulling
the Trigger Switch again.
• Low battery voltage: The remaining Battery capacity is
See Fig. A1
too low and the tool will not operate. In this situation, remove
and recharge the Battery Pack.
See Fig. A2, A3
See Fig. A4
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN YOU
PRESS THE SWITCH?
The Forward and Reverse Switch, which is on top of the
trigger, is positioned in the lock function. Unlock the
Forward and Reverse Switch putting it into the required
rotation position. Push the trigger and the drill will start
to rotate (See Fig.B)
See Fig. B1
2. THE DRILL STOPS BEFORE THE SCREW IS
COMPLETELY TIGHTENED. WHY?
See Fig. B2
Verify the torque position of the Torque Adjustment
Ring, you can find the Torque Adjustment Ring between
the Chuck and the drill body. Position 1 is the lowest
torque (screw driving force) and position 18 is the
highest torque (screw driving force). Position is for
drill operation. Position
See Fig.C1,
Regulate the Torque Adjustment Ring to a higher position
C2, C3
to reach the best result. (See Fig. E1, E2, E3)
3. I CAN NOT FIT THE BATTERY PACK INTO THE
See Fig. D
BATTERY CHARGER. WHY?
The battery pack can be inserted into the charger only in
one direction. Turn the battery pack around until it can be
See Fig. E1,
inserted into the slot. The charger LED indicator should
E2, E3
turn on when the battery pack is charging.
4. REASONS FOR DIFFERENT BATTERY PACK
See Fig. F
is for hammer drill operation.
EN
Publicité
