Publicité
WARNING! Risk to life! When exceed-
ing the maximum payload, there is a risk
of life-threatening injuries!
WARNING! Risk to life! Before use,
ensure that the vehicle to be lifted will not
be damaged by the vehicle jack. Use
blocks to secure the vehicle and prevent it
from rolling away. There is a danger of
life-threatening injuries!
► P. 4, fig. 3
– Unfold enclosed chocks as shown.
– Use blocks to prevent the vehicle from rolling
away. To do this, place a block both in front and
behind a tyre.
– Press the securing brake and select the first gear
or the "P" lifting setting.
– Slide the car jack under the vehicle such that the
disc rests under the designated receiver.
► P. 4, fig. 4
– Slip the handle bar onto the lowering valve (12).
Close the lowering valve by turning it clockwise.
– Insert the handle bar into the receiver (11) and
lock it into place by turning it briefly.
– Lift the load to the desired height by repeatedly
lifting and lowering the handle bar.
Secure loads
– Make sure the surface under the support trestles
is level and sufficiently strong.
– Slide the support trestles under the vehicle at the
designated position.
– Adjust the support (7) to the necessary height.
– Lower the load carefully until it rests on the sup-
port trestles.
– Remove the car jack.
WARNING! Risk caused by falling
loads! Bolt and securing pin must always
be fully inserted when using the support
frame.
Lowering loads
WARNING! Risk to life! Ensure slow
and controlled lowering of the vehicle
jack. When the load is dropped suddenly,
there is a risk of life-threatening injuries!
– Make sure there are no persons, animals or
objects under the load.
– Slip the handle bar onto the lowering valve (12).
Slowly open the lowering valve by turning it coun-
terclockwise.
• The load and the lifting arm will drop.
Maintenance and storage
Maintenance
– Check the hydraulic cylinder and car jack regu-
larly for corrosion and loss of oil. Cleans any
unprotected areas with a clean cloth.
– Use a suitable lubricant to grease all moving
parts.
– Prior to every use, check if all parts of the device
are complete and undamaged.
Bleeding the hydraulics
If the lifting performance of the device decreases,
bleed air from the hydraulic cylinder.
– Open the lowering valve (at least two full counter-
clockwise rotations).
– Actuate the handle bar at least twenty times.
Refilling hydraulic oil
NOTICE! Environmental damage!
Hydraulic oils are very hazardous to the
environment! Wipe away spilt hydraulic oil
immediately.
If the unit cannot be extended to the full height, the
hydraulic oil needs to be topped up.
NOTICE! Machine damage! Only use
suitable hydraulic oil (► Technical data).
Filling the unit with motor oil, brake fluid or
other unsuitable liquids may damage the
unit.
– Remove the cover (5).
– Open the filler plug on the hydraulic cylinder and
refill clean hydraulic oil.
Adjusting the hydraulics
– Close the lowering valve.
– Manually pull out the jack as far as possible.
– Open the lowering valve and lower the jack.
Storing
CAUTION! Risk of injury! Store the
device in such a way that it cannot be
started by unauthorised persons.
Ensure that no one is able to hurt them-
selves on the stored unit.
NOTICE! Machine damage! Store the
device in a dry and well ventilated place.
– Keep the unit closed up in a dry environment to
prevent corrosion damage.
Transport
– If shipping, use the original packaging wherever
possible.
Preparing for disposal
NOTICE! Environmental pollution! The
device is filled with a particular quantity of
special oil. Repairs which require the
opening of the oil tank may only be carried
out by the manufacturer or its customer
service partner.
Follow guidelines with respect to disposal
of the oil and scrapping of the device.
Disposal
Disposal of the appliance
This appliance must not be disposed of with regular
household waste! Dispose of the appliance in the
appropriate manner. For more information, consult
your community waste disposal service.
GB
19
Publicité
