Télécharger Imprimer la page

Hoover SMARTWASH FH52110 Mode D'emploi page 3

Publicité

HOW TO REMOVE & CLEAN
NOZZLE
WARNING:
Risk of personal injury
– Brush roll may suddenly restart – unplug
before cleaning or servicing .
1
To prevent possible leaking, remove and empty
Clean Water Tank and Dirty Water Tank.
2
With handle in upright position, lift up on the
Nozzle release then pull Nozzle forward to
remove from carpet cleaner.
CAUTION:
Pull Nozzle carefully
outwards and not upwards.
3
Rinse debris from Nozzle.
HOW TO REMOVE & CLEAN
BRUSH
WARNING:
Risk of personal injury
– Brush roll may suddenly restart – unplug
before cleaning or servicing
.
1
To prevent possible leaking, remove Clean
Water Tank and Dirty Water Tank.
2
With handle in upright position, lift up on the
Nozzle release then pull Nozzle forward to
remove from carpet cleaner.
A
3
Grab Side A and pull up to remove.
4
The brush can be cleaned under running water.
HOW TO REPLACE BRUSH
1
B
At an angle, align side B on the brush to the
drive gear.
A
2
Press Tab A down until brush snaps in place.
LUBRICATION:
The motor and
brushroll are equipped with bearings which
contain sufficient lubrication for their
lifetime. The addition of lubricant could
cause damage. Do not add lubricant to motor
or brushroll.
STORAGE:
Before storing: Empty Clean Water Tank
and let air dry. Replace on cleaner. Empty
Dirty Water Tank, clean filter of dirt/
debris, rinse tank and lid thoroughly with
clean water and let air dry. Allow brush
and underside of carpet cleaner to air dry
thoroughly before storing carpet cleaner on a
carpeted or wood surface.
CORD STORAGE:
Wrap the power
cord around the cord hooks for convenient
storage. Attach the plug end to the cord.
HOW TO ATTACH & REMOVE TOOLS
CAUTION:
Not to be used for
grooming a pet.
1
To ensure maximum performance and to
protect your carpet, be sure to place the handle
in the upright position while using the hose.
Placing the handle in the upright position shuts
off the FlexForce™ PowerBrush.
2
Connect tool to hose by sliding it onto the
connector until it securely locks into place.
3
To remove tool, use your thumb, push forward
and up on the latch.
CLEANING CARPETED STAIRS
AND UPHOLSTERY
CAUTION:
Use extra care when
cleaning on stairs. To avoid personal injury
or damage, and to prevent the cleaner from
falling, always place cleaner at the bottom
of stairs or on floor. Do not place cleaner on
stairs or furniture, as it may result in injury
or damage.
1
Attach hose as instructed above.
2
Place handle in upright position. FlexForce™
PowerBrush will not rotate while handle is in
the upright position.
3
Fill Clean Water Tank with clean water and
Hoover® solution according to instructions.
4
Attach tool to end of hose.
5
Dry hands and plug cleaner into a properly
grounded outlet.
6
Turn cleaner ON.
7
Pre-spray the area by holding the tool about
one inch above the carpet and push it forward
while pressing the trigger.
8
Slightly press the tool switch into area
cleaning. Press the trigger and pull the tool
slowly over the carpet. Release trigger at end
of stroke.
9
Lift tool, and position it against Nozzle. Pull
tool slowly over carpet without pressing
trigger.
10
Overlap strokes by ½ inch to help prevent
streaking.
11
It is best to alternate wet and dry strokes as
described in steps.
TIP
To avoid saturating carpet, do not
use more than 4 wet strokes over
any one area. Always end with dry
strokes.
If additional cleaning is necessary,
wait until the carpet is completely
dry before using the tool again.

Publicité

loading