Télécharger Imprimer la page

Palram Canopia MILANO 10x10 / 3x3 Mode D'emploi page 38

Masquer les pouces Voir aussi pour Canopia MILANO 10x10 / 3x3:

Publicité

EN
INFORMATION
SAFETY ADVICE
SAFETY ADVICE & CAUTIONS!
It is of utmost importance to assemble all of the parts according to the directions. Do not skip any steps.
Always wear work gloves during panel sliding.
• •
These products may represent a possible shock or fire hazard if improperly installed or
1.
Always wear shoes and safety goggles when working with extruded aluminium.
• •
attached in any way. Products should be installed in accordance with the owners manual,
If using a step ladder or power tools make sure that you follow the manufacturer's safety advice.
• •
Do not touch overhead power cables with the aluminium profiles.
current electrical codes and/or the current National Electric Code (NEC).
• •
Do not attempt to assemble the product in windy or wet conditions.
• •
Though This fixture is IP67 with weather protection and can stand high humidity environments
2.
Do not climb or stand on the roof.
• •
you have to carefully plan the fixture plug positioning and protection. The connection between
Dispose of all plastic bags. Keep them out of reach of small children.
• •
the fixture plug to the electric plug should be water protected.
Keep children away from the assembly area.
• •
Do not lean against or push the products during construction.
This appliance can be used by children aged from 8 years and above and persons with
3.
• •
Do not position your product in an area exposed to excessive winds.
• •
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells.
• •
have been given supervision or instruction concerning use of the appliance in a safe way and
Hot items such as recently used grills, blowtorches etc. must not be stored in the product.
• •
understand the hazards involved. Children shall not play with the appliance. Cleaning and user
Make sure there are no hidden pipes or cables in the ground before anchoring to foundation.
• •
This product is designed to be used mainly as a greenhouse.
maintenance shall not be made by children without supervision.
• •
Make sure to anchor the product directly to a solid foundation to increase the product's stability and wind resistance in areas with
• •
Children aged from 3 years and less than 8 years shall only switch on/off the appliance
4.
severe weather conditions. Make sure that there are no obstructions between the assembly area and the final position of the product.
provided that it has been placed or installed in its intended normal operating position and they
The Palram - Canopia Anchoring kit is available for purchase separately.
have been given supervision or instruction concerning use of the appliance in a safe way and
CARE & MAINTENANCE
understand the hazards involved. Children aged from 3 years and less than 8 years shall not
plug in, regulate and clean the appliance or perform user maintenance.
When your product needs to be cleaned, use a mild detergent solution and rinse with cold clean water.
The power coupler is waterproof when not in use. In order to prevent possible electric shock or
5.
DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels.
• •
leakage current, never use the appliance with wet hand or operate the appliance when there is
Clean the product once assembly is complete.
• •
water on the power cord.
BEFORE ASSEMBLY
If using a stepladder or power tools please make sure that you follow the manufacturer's
6.
safety advice.
Selecting a site:
- Choose your site carefully before beginning assembly.
- Choose a sunny position away from overhanging trees.
- The product must be positioned and fixed on a flat level surface.
The product must be secured directly to a solid foundation.
• •
This is a multi-part assembly best achieved by two people. Allow at least half a day for the assembly process.
• •
Take all components & parts out of the packages. Sort the parts and check against the content parts list.
• •
Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.
• •
Please note multi-sided profiles are used in this product. As a result some holes in the profiles are not used during assembly.
• •
Please review entire instructions before starting. Carry out the assembly steps in exact order.
• •
Please consult your local authorities if any permits are required prior to constructing the product.
TOOLS & EQUIPMENT
• •
Please ensure you have sufficient side space for inserting the roof panels during the assembly process.
• •
IMPORTANT!
… 1 person
Firmly connect the product to a level surface immediately after completion of the assembly.
needed
Anchoring this product to the ground is essential to its stability and rigidity. It is required to complete this stage in order for your warranty to be valid.
• •
During assembly use a soft surface below the parts to avoid scratches and damages.
• •
We recommend checking for restrictions or covenants for building this product in your area.
• •
In addition we advise to check if you need to submit any forms or if any permit is required prior to building the product.
… Philips Head
… Cordless Drill -
Screwdriver
Philips Head
DURING ASSEMBLY
BEFORE ASSEMBLY
During assembly, you will encounter different icons for different products.
Please see below for more information:
Please read these instructions carefully before you start to assemble this product.
• •
Please carry out the steps in the order set out in these instructions.
• •
Keep these instructions in a safe place for future reference.
• •
The system is suitable to be mounted onto straight, not curved, profiles.
• •
SILICONE
LUBRICANT SPRAY
It is not possible to assemble a curtain / netting kit in addition to the Lighting System.
• •
DURING ASSEMBLY
LED Type: 4000K.
• •
The lighting system is supplied without an electrical plug, you must contact a qualified
• •
electrician for the purpose of assembling an electrical plug that complies with the standard in
your country.
Please make sure that your electrical system is ready and working properly up to the point of
• •
connection of the transformer.
The cable's length, from the light fixture to the plug is 120 cm (47.2"), please plan the placement
• •
of the light fixture and the transformer accordingly.
Profile #8774 is supplied in black and white, use the suitable profile to your product's color.
• •
In this instruction manual we show the Lighting System's assembly onto a patio cover,
• •
however, this Lighting System is compatible with our range of Patio Covers, Garden Chalet,
Gazebos, Greenhouses, Sheds & Carports.
The mounting of the Lighting System is performed onto the screws channels in the
• •
aluminum profiles.
Extension Kit
… Ladder
You may use silicone lubricant spray on the frame in order to help
you slide the panels into the profiles. Do not spray the panels.
Use a rubber mallet if necessary.
Make sure you remove covering plastic film from both sides
of the panel.
All panels with the stamped words "THIS SIDE OUT" must be
facing out to create full UV protection. Remove plastic sticker
as panels are locked in place.
This icon indicates that the installer should be inside
the product.
This icon indicates that the installer should be outside
the product.
Steps marked with dashed outlines refer to Extensions only.
Some of the steps are irrelevant for an assembly of a single product.
When assembling a single or an extended product,
some parts may be surplus.
These 2 icons below indicate if screw's tightening is
required or not.
… Electric drill -
Temporary tightening of a few screws may be needed to
Drill bit
… Utility Knife
prevent a profile from sliding out.
4 mm | 1/64"
Tighten all screws once assembly is completed.

Publicité

loading