Publicité
Product Maintenance
Cleaning Side Brushes
ct Maintenance
Product Maintenance
Cleaning Side Brushes
Clean the side brush when it become dirty and replace it if it's damaged. The maximum life span of
g Side Brushes
Cleaning Side Brushes
the side brush is 12 months.
Clean the side brush when it become dirty and replace it if it's damaged. The maximum life span of
ct Maintenance
Note: Before replacing side brushes, check and ensure that the L/R mark on the side brush match
Charging without a charging station
the side brush is 12 months.
side brush when it become dirty and replace it if it's damaged. The maximum life span of
Clean the side brush when it become dirty and replace it if it's damaged. The maximum life span of
Plug the adapter into the contact and insert the DC input into
with the L/R mark on the bottom base of the robot.
Note: Before replacing side brushes, check and ensure that the L/R mark on the side brush match
ush is 12 months.
the vacuum.
he side brush is 12 months.
g Side Brushes
with the L/R mark on the bottom base of the robot.
Cleaning Dust Bin and Filters
·
While charging:
re replacing side brushes, check and ensure that the L/R mark on the side brush match
Note: Before replacing side brushes, check and ensure that the L/R mark on the side brush match
Cleaning Dust Bin and Filters
side brush when it become dirty and replace it if it's damaged. The maximum life span of
·
R mark on the bottom base of the robot.
with the L/R mark on the bottom base of the robot.
Empty and clean the dust bin after each usage following the steps as show in the figures below:
·
ush is 12 months.
Empty and clean the dust bin after each usage following the steps as show in the figures below:
g Dust Bin and Filters
·
Cleaning Dust Bin and Filters
re replacing side brushes, check and ensure that the L/R mark on the side brush match
R mark on the bottom base of the robot.
clean the dust bin after each usage following the steps as show in the figures below:
mpty and clean the dust bin after each usage following the steps as show in the figures below:
CLEANING AND MAINTENANCE
g Dust Bin and Filters
CLEANING OUT THE CANISTER AND FILTER
d clean the dust bin after each usage following the steps as show in the figures below:
Clean the canister and the filter after each use in the following manner:
1
A. Hold the bottom of dust bin, and press down on the button using your
A. Hold the bottom of dust bin, and press down on the button using your
thumb to take out of the dust bin.
thumb to take out of the dust bin.
e bottom of dust bin, and press down on the button using your
A. Hold the bottom of dust bin, and press down on the button using your
take out of the dust bin.
thumb to take out of the dust bin.
e bottom of dust bin, and press down on the button using your
3
take out of the dust bin.
C. After press down button
C. After press down button
and o
pen dust bin upper cover
and o
pen dust bin upper cover
5
press down button
C. After press down button
D. Open dust bin cover and take out the
dust bin upper cover
and o
pen dust bin upper cover
press down button
primary filter and HEPA filter.
dust bin upper cover
F. Wash the dust bin and primary filter under tap water,
F. Wash the dust bin and primary filter under tap water,
1.
Press the button that opens the canister. Remove the canister from the vacuum.
clean the HEPA filter with brush, avoid washing it under
clean the HEPA filter with brush, avoid washing it under
2.
Press the open button to open the canister.
water.
water.
3.
Remove the HEPA filter, including the holder, from the canister.
4.
Empty the canister into the waste bin.
5.
Rinse the canister and filter holder under running water. Let them dry before putting them back in
e dust bin and primary filter under tap water,
F. Wash the dust bin and primary filter under tap water,
place. Clean the HEPA filter with the dust brush.
HEPA filter with brush, avoid washing it under
e dust bin and primary filter under tap water,
clean the HEPA filter with brush, avoid washing it under
·
HEPA filter with brush, avoid washing it under
water.
·
6.
Replace the HEPA filter and holder in the canister. To do this, first turn the cover to the side.
www.domo-elektro.be
Display shows flashing '1111': vacuum is charging
Display shows 'FULL': device is fully charged
Display shows 'Erro': the power switch must be on to
charge
D. Open dust bin cover and take out the
D. Open dust bin cover and take out the
primary filter and HEPA filter.
primary filter and HEPA filter.
D. Open dust bin cover and take out the
D. Open dust bin cover and take out the
primary filter and HEPA filter.
primary filter and HEPA filter.
G. Assemble primary filter and HEPA filter again into
If the HEPA filter is dirty, after about 30 days of use, you can also clean it under running water. Let
G. Assemble primary filter and HEPA filter again into
dust bin.
it dry before putting it back in place.
dust bin.
The HEPA filter must be replaced after frequent use. The maximum service life of the filter is
approximately 6 months.
16
16
Charge the robot in either way as shown below:
2.
Cleaning Side Brushes
A.
Plug one end of the adapter into the robot and the other end into the
Clean the side brush when it become dirty and replace it if it
in Fig a.
B.
Press the "HOME" button on the remote control or robot to operate
the side brush is 12 months.
charging docking automatically as shown in Fig b.
Note: Before replacing side brushes, check and ensure that
with the L/R mark on the bottom base of the robot.
Cleaning Dust Bin and Filters
Empty and clean the dust bin after each usage following the
Note:
a.
When robot is in charging, the LED panel will gradually show "1111"
b.
When charging is over, the LED panel will show "FULL".
c.
In standby status, the robot will
2
d.
In working status, the robot will look for the charging dock automatic
level is low.
In Order to Extend Battery's Life
a.
Please charge the robot for up to 5 hours during the first charging.
b.
Charge the robot as soon as possible when battery capacity is low.
B. Take out dust bin.
c.
The robot will return to the charging dock automatically when clean
B. Take out dust bin.
capacity is low.
d.
When you do not use the robot for some time, please fully charg
B. Take out dust bin.
4
switch off the robot and keep it in a cool but dry place.
e.
If the robot has been put aside over 3 months, please charge th
before using it for cleaning.
6
E. Empty the dust bin.
E. Empty the dust bin.
E. Empty the dust bin.
G. Assemble primary filter and HEPA filter again into
G. Assemble primary filter and HEPA filter again into
dust bin.
dust bin.
G. Assemble primary filter and HEPA filter again into
16
16
dust bin.
16
Fig a
A. Hold the bottom of dust bin, and press down on the button usi
thumb to take out of the dust bin.
B. Take out dust bin.
B. Take out dust bin.
C. After press down button
and o
pen dust bin upper cover
E. Empty the dust bin.
E. Empty the dust bin.
F. Wash the dust bin and primary filter under tap water,
clean the HEPA filter with brush, avoid washing it under
water.
show
when the battery leve
D. Open dust bin cover and take
primary filter and HEPA filter.
10
G. Assemb
dust bin.
16
43
DO7293SN
F
Publicité
