Publicité
To reduce the risk of explosion,
WARNING
electric shock and property dam-
age, always check the work area for hidden gas
pipes, electrical wires or water pipes when mak-
ing blind or plunge cuts.
Plunge Cutting
This MILWAUKEE Sawzall
ting directly into surfaces that can not be cut from
an edge, such as walls or floors. Plunge cutting may
be done two ways depending on how the blade is
inserted. Column A shows how to plunge cut with the
teeth of the blade facing downward. Column B shows
how to plunge cut with the teeth of the blade facing
upward. Do not plunge cut into metal surfaces (see
"Cutting Metals").
1. Insert the blade into the tool.
If you inserted the blade with the teeth facing
downward, hold the tool as shown in Column A,
resting the edge of the shoe on the workpiece.
If you inserted the blade with the teeth facing up-
ward, hold the tool as shown in Column B, resting
the edge of the shoe on the workpiece.
2. With the blade just above the workpiece, pull the
trigger. Using the edge of the shoe as a pivot, lower
the blade into the workpiece as shown.
3. As the blade starts cutting, raise the handle of
the tool slowly until the shoe rests firmly on the
workpiece. Then guide the tool along your cutting
line to acquire the desired cut.
NOTE: To make plunge cutting easier, use a heavy
gauge blade and install the blade with the teeth facing
upward as shown in Column B.
A
®
is ideal for plunge cut-
B
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the battery pack, charger, or tool, except as pro-
vided in these instructions. Contact a MILWAUKEE
service facility for all other repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from any vents. Keep tool
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.
ACCESSORIES
Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
6
Cleaning
Repairs
(1.800.729.3878)
Publicité
