Product Dimensions; Cabinet Dimensions - Whirlpool W11241780A Instructions Pour L'installation

Product Dimensions

A**
F
A. 35³⁄ " ± ¹⁄ " (90.8 ± 0.3 cm)
4 8
cooktop height (minimum) with
leveling legs screwed all the way
in
B. Model/serial/rating plates
(located behind the control
panel)*
* Model/serial/rating plates may be rotated up from behind the
control panel for viewing from the front of the range.
**Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
***Excludes handle. Dimension given is from wall to front of
oven door and will vary based on electrical outlet receptacle
installation.

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and 36"
(91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood
combination above the cooking surface, follow the range hood
or microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
Range may be installed with zero clearance to combustible
construction at the rear and on the sides below the cooktop.
B*
C**
D
E***
C. 47 ⁄ " ± ¹⁄ " (120.3 ± 0.3 cm)
3
8 8
overall height (minimum) with
leveling legs screwed all the way
in**
D. 28¹⁄ " ± ¹⁄ " (72.4 ± 0.6 cm) depth
2 4
with handle
E. 26¹⁄ " ± ¹⁄ " (66.4 ± 0.3 cm)***
8 8
F. 29¹ 5 ⁄ " ± ¹⁄ " (76.0 ± 0.2 cm)
16 16
width
8½"
(21.6 cm )
1½"
(3.8 cm )
(3.1 cm )
A. 18" (45.7 cm) upper cabinet to countertop
B. 13" (33.0 cm) upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to the top of the cooktop, see NOTE.
E. in U.S.A.: 30" (76.2 cm) min. opening width
in Canada: 31" (78.7 cm) min. opening width
F. 3" (7.6 cm) min. clearance from both sides of the range to the
side wall or other combustible material.
G. Cabinet door or hinges should not extend into the cutout.
H. 3" (7.6 cm) distance from wall
I. 1¹⁄ " (3.8 cm) min. from right side cabinet
2
J. 8" (20.3 cm) width
K. 7" (17.8 cm) min. from floor
L. 2" (5.1 cm) min. from floor
* Drill on centerline 1¼" (3.1 cm) from rear wall for gas supply
line.
**Gas lines must be installed within the shaded area to ensure
proper alignment of this oven with cabinets.
***Recessed electrical plugs must be installed within the shaded
area to ensure proper alignment of this oven with cabinets.
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal
cabinet is covered by not less than ¹⁄
millboard covered with not less than No. 28 MSG sheet steel,
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or
0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an uncovered wood or metal cabinet.
14"
***
(35.6 cm )
2¼" (5.7 cm )
1¼"*
8½" (21.6 cm)* *
gas line location
" (6.3 mm) flame retardant
4
5