Publicité
- Disregarding instructions detailed in thisinstruction sheet will involve
dangerous use of the product, with fall and/or shock hazard.
Before assembly, ensure that:
1- The place where you build the product is:
- Plane and horizontal.
- Minimum 2 meters(6.6 ft) away from any object, structure or other obstacle
(hedge, tree, clothesline, electrical line...) that could hurt product user.
- Not on a hard floor (concrete, asphalt...). Select grass or other kind of soft
floor (sand, shock absorbing materials...).
2- Fastening is complete. You could have unused parts at the end of the
assembly, keep them for further use (spare parts).
When the product is equipped with a slide, we advise you to set it not directly
facing the sun.
After assembly:
- Fix the product on concrete anchors, realized by following instructions
detailed on this instruction sheet.
NB: concrete blocks must be fully dry before fixing the product on them. Only
metalstake shall be drowned into concrete.
No other part of the product shall be drowned into concrete.
- When needed, adjust apparatus setting (see figure Y).
- Check distance between apparatus bottom surface and the ground.
Distances must be respected to enable a safe use of the product.
If they are below the specifications indicated in figure W, use the plastic rings
to adjust the height of the seat. If this is not possible, please contact our
after-sales service.
GROUND ANCHORING (see figure Z)
1- Build the product, and set it on the selected place.
2- Mark anchors position.
3- Check on your product dimensions indicated in figure W, adjust them if
necessary.
4- Under each anchor position, mark a 30 cm x 30 cm(11.8" x 11.8") square,
and dig it to 30 cm(11.8") depth.
5- Fill these holes with concrete following figure Z. Dome extremity shall not
exceed floor level, to prevent from stumbling.
10
6- Put anchor on concrete on the marked position (see point 2). Warning: only
the drilled side of the anchor shall be over the concrete.
7- Once concrete is dry, screw legs of the product on anchors.
8- Wait for complete drying of concrete before using the product.
9- Cover with ground each anchor, to prevent from stumbling.
Check regularly every anchoring point.
Maintenance instructions
To avoid any danger by using the product, several points must be checked
every month:
- To check swing seats, ropes and other means of attachments for evidence of
deterioration.
- Suspension hooks and hinge. Change them if wear is 10 % more than
original thickness.
- To replace defective parts in accordance with the manufacturer's instructions.
- To check all nuts and bolts, structure and apparatus screws and nuts
tightening: tighten again if necessary.
- To check all covering for bolts and sharp edges and replace when required;
Presence of nuts caps. Replace them by identical nuts cap if they are missing.
- Anchors resistance.
- Plastic part general condition. Replace them if they are cracked or drilled.
- Wear indicator: apparatus must be changed when metal part is visible on the
plastic ring.
- If the product is equipped with fabrics, they must be cleaned with a damp
sponge. Do not use washing products.
- To prevent the product for deteriorations due to weather conditions, remove
and store all apparatus and accessories of the product during winter period.
- If corrosion occurs on metallic parts, clean them with a suitable product. If
corrosion is still progressing, contact our after-sales service.
- Keep a watch on the floor where the product is installed, remove stones and
all other object that could hurt users in case of falling.
Timber advice
This product has been made from timber. Great care has been taken in
selecting, treating and machining the timber before it is presented to you.
Timber is a natural product and as such many experience changes throughout
the course of its life. This means it may:
- Develop openings (gaps, slits, apertures, cracks, splits) along the line of the
grain. These openings are due to the difference in moisture content between
the internal and outer surfaces of the timber. This is to be expected, is totally
acceptable and will not affect the integral strength, life or guarantee of the
product.
11
Publicité
