Publicité
•
Place the saw foot flat on the workpiece you
wish to saw. The saw blade must not be in
contact with the workpiece.
•
Hold the circular saw firmly with both hands.
6.3 Switching ON/OFF (Fig. 12)
To switch on:
Press the locking button (3) and the ON/OFF
switch (2) at the same time
•
Allow the saw blade to accelerate until it
reaches full speed. Then slowly move the saw
blade along the cutting line. Only exert gentle
pressure on the saw blade as you do so.
To switch off :
Release the locking button and ON/OFF switch
•
If you release the handle the equipment will
shut down automatically which means that it
cannot operate accidentally.
•
Ensure that you do not cover or block the ven-
tilation openings whilst working with the tool.
•
Do not slow down the saw blade after you
switch it off by pressing it sideways.
•
Important! Do not put down the machine until
the saw blade has reached a complete stand-
still.
Important. Carry out a trial cut in a piece of
waste wood
6.4 Changing the saw blade (Fig. 13-18)
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Use only saw blades which comply with standard
EN 847-1 and are of the same type as the saw
blade supplied with this circular saw. Ask your
dealer for advice.
Warning!
Do not use grinding wheels!
The diameters of the saw blades used must cor-
respond to the diameters specifi ed on the hand-
held circular saw blade!
Use only recommended saw blades!
Use the saw blade key (13) supplied to change
the saw blade. The saw blade key (13) is stored
in the housing. If required, pull the saw blade key
(13) out of the housing (see Figure 13).
Anl_TP-CS_18-165_Li_BL_SPK13.indb 22
Anl_TP-CS_18-165_Li_BL_SPK13.indb 22
GB
Important. The hand-held circular saw must not
be operated with the saw blade key (13) inserted
in it.
•
Press the spindle lock (11).
•
Undo the screw to secure the saw blade (17)
using the saw blade key (13).
•
Push back and secure the moving swing
guard hood (20) using the lever for the swing
guard hood (21).
•
Remove the flange (18) and the saw blade
(12) in a downwards direction.
•
Clean the flange and insert the new saw bla-
de. Pay attention to the running direction (see
arrow on the guard hood and saw blade).
•
Remove the clamping flange (18) and the
saw blade (12) in a downwards direction.
•
The circular saw is equipped with a change
flange (19) which can be turned to allow both
saw blades with a 16mm mounting hole and
saw blades with a 20mm mounting hole to be
fitted.
•
To mount a 16mm saw blade, fit the change
flange (19) as shown in figure 17.
•
To mount a 20mm saw blade, fit the change
flange (19) as shown in figure 18.
•
Clean the clamping flange (18) and then fit
clamping flange (18) and new saw blade. Pay
attention to the running direction (see arrow
on the guard hood and saw blade).
•
Tighten the screw to secure the saw blade
(17), check it runs true.
•
Before you press the On/Off switch, make
sure that the saw blade is correctly fitted and
that moving parts run smoothly and the clam-
ping screws are tightened securely.
6.5 LED lamp (Fig. 1/Item 5)
The LED lamp (5) can be used in poor lighting
conditions to additionally illuminate the cutting
position. The LED lamp (5) will come on automa-
tically as soon as you press the locking button for
the On/Off switch (3).
- 22 -
29.04.2024 13:19:07
29.04.2024 13:19:07
Publicité
