Publicité
2. PLACE THE BASE ON A FLAT, STABLE, HEAT-RESISTANT SURFACE AWAY FROM WATER
SPLASHES AND ANY SOURCES OF HEAT.
• Kettle is only to be used with the base provided.
3. FILL THE KETTLE WITH THE DESIRED AMOUNT OF WATER.
• Never fill the kettle when it is on its base.
• Do not fill it above the maximum level, or below the minimum level. If the kettle is too full,
boiling water may spill out.
• Do not use without water.
• Check that the lid is closed properly before use.
4. POSITION THE KETTLE ON ITS BASE. PLUG IT INTO THE MAINS SOCKET.
5. TO START THE KETTLE
When the kettle is placed on the base, all the lights illuminate. The water temperature in the kettle
is displayed on-screen.
TO HEAT WATER:
2 options:
• If you wish to start a boil cycle, press the
a long beep. The kettle then shows the real water temperature and starts heating the water.
• If you wish to select the temperature – 5 possible settings: 40°C – 70°C – 80°C – 90°C – 100°C –
press the
key until it displays the temperature you wish to select. The selected temperature
blinks 4 times, accompanied with a long beep. The kettle then shows the real water temperature
and starts heating the water.
You can monitor the live temperature of the water on the screen.
Once the selected temperature is reached, the kettle beeps twice and stops heating.
If you wish to turn off the heating programs, just press the
PLEASE NOTE
After 90°C, the kettle will boil water, stop, then restart boiling water. This circulation will happen
several times and continue to the end of the heating process.
KEEP WARM MODE
You can use the keep warm mode to keep the water at your desired temperature during 30 minutes.
Once the temperature has been selected, a long push on
mode at selected temperature. 2 lights around the
You can also start the keep warm mode once the temperature has been reached. Do a long push
on the
or
key. The
will let you keep warm at selected temperature, while
you keep warm at 95°C. 2 lights around the
If you wish to turn off the keep warm mode, just press the
PLEASE NOTE
The long push will activate the keep warm only if you push the button less than 30 seconds after
the end of the boiling cycle, otherwise the screen will switch off.
PLEASE NOTE
The screen automatically switches off after 30 seconds – unless you have selected the keep warm
mode – but pressing any key will turn the screen on again anytime.
If you select 100°C and activate the keep warm function, the kettle keeps the temperature at 95°C
for 30mins.
If the temperature of the water in the kettle is higher than the temperature you select when
pressing
, the heating won't start.
For instance, if the water temperature is 90°C, you won't be able to launch the heating by
selecting 40°C, 70°C or 80°C.
(fig 3)
button, the 100° blinks 4 times, accompanied with
or
.
or
will activate the keep warm
will be illumed.
will let
will be illumed.
or
key.
6
RECOMMENDED TEMPERATURES
40°C: baby milk
70°C : white tea
80°C : green tea
90°C : freshly ground coffee
100°C : boiling water/infusions
6. THE KETTLE WILL SWITCH OFF AUTOMATICALLY
As soon as the water reaches boiling point or the chosen temperature.
• Do not leave water in the kettle after use as this quickens the formation of scale.
CLEANING AND MAINTENANCE
CLEANING YOUR KETTLE
Unplug it.
Let it cool down and clean it with a damp sponge.
• Never immerse the kettle, its base, the cord or the electric plug in water: the electrical
connections or the switch must not come into contact with water.
• Do not use scouring pads.
• Do not wipe the display while plugged in, it may cause unexpected start-up.
CLEANING THE FILTER*
The removable filter consists of a mesh to retain the particles of scale and prevent them falling into your
cup when pouring. This filter neither treats nor removes the hardness of the water. It thus conserves
all the qualities of the water. With very hard water, the filter can clog very quickly (10 to 15 uses). It is
important to clean it regularly. Sometimes the scale will not detach itself; it will then need descaling.
DE-SCALING
De-scale regularly, preferably at least once a month or more frequently if your water is very hard.
Temperature detection in the kettle may be affected by limescale.
To de-scale your kettle:
• Using white vinegar which can be bought from hardware stores:
– Fill the kettle with ½ litre of white vinegar,
– Leave to stand for 1 hour without heating.
• Using citric acid:
– Boil ½ litre of water,
– Add 25 g of citric acid and leave to stand for 15 min.
• Empty your kettle and rinse 5 or 6 times. Repeat if necessary.
To de-scale your filter*:
Soak the filter in white vinegar or diluted citric acid.
• Never use a de-scaling method other than that recommended.
IN THE EVENT OF PROBLEMS
THERE IS NO EVIDENT DAMAGE TO YOUR KETTLE
• The kettle does not work
– Check that your kettle is properly connected.
– The kettle has been switched on without water or an accumulation of scale has caused the
overheat cut-out to operate: allow the kettle to cool and fill it with water. Descale first if scale
has accumulated.
Switch it on: the kettle should start working again after about 15 minutes.
* according to models
7
EN
Publicité
