Metabo BF 18 LTX 90 Notice Originale page 13

For optimum operation: Sand on the side on which
the sanding belt moves towards the machine.
11. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
Battery packs with different capacities:
18 V Li-Power 4,0 Ah ............................... 6.25591
18 V Li-Power 5,2 Ah ............................... 6.25592
18 V LiHD 5,5 Ah ..................................... 6.25342
18 V LiHD 8,0 Ah ..................................... 6.25369
Chargers:
AS 55
ASC 145 etc.
For a complete range of accessories, see
www.metabo.com or the main catalogue
12. Repairs
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Battery packs must not be disposed of with regular
waste. Please return faulty or used battery packs to
your Metabo dealer.
Do not throw battery packs into water.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-
circuiting (e. g. by protecting them with adhesive
tape).
14. Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U = Voltage of battery pack
B = Sanding belt length
L
v = Belt speed in idling
0
m = Weight with smallest battery pack
Measured values determined in conformity with EN
62841.
Permitted ambient temperature during operation:
-20 °C (-4°F) to 50 °C (120°F) (limited performance
with temperatures below 0 °C (32°F)). Permitted
ambient temperature for storage: 0 °C (32°F) to
30 °C (86°F).
Direct current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a = Vibration emission value (sanding
h
surfaces)
K = Uncertainty (vibration)
h
The vibration emission level given in this
information sheet has been measured in
accordance with a standardised test given in EN
62841 and may be used to compare one tool with
another. It is also suitable for a provisional estimate
of the vibratory load.
The specified vibration level applies to the main
applications of the power tool. However, if the tool is
used for other applications, with different
accessories or is poorly maintained, the vibration
level may vary. This can considerably increase the
vibratory load over the entire working period.
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not
actually doing the job. This can considerably reduce
the vibratory load over the entire working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
A-effective perceived sound levels:
L = Sound pressure level
pA
L = Acoustic power level
WA
K , K = Uncertainty (noise level)
pA WA
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
ENGLISH en
13