Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. CP0168
  6. Instructions de montage

R&G CP0168 Instructions De Montage

Masquer les pouces
1
2
3
4
5
6
7
8

Publicité

Liens rapides

Télécharger ce manuel
Page 1 of 8
CP0168
FITTING INSTRUCTIONS CP0168 CRASH PROTECTORS
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

loading

Manuels Connexes pour R&G CP0168

Sommaire des Matières pour R&G CP0168

  • Page 1 Page 1 of 8 CP0168 FITTING INSTRUCTIONS CP0168 CRASH PROTECTORS HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
  • Page 2 Page 2 of 8 CP0168 TOOLS REQUIRED GENERAL TORQUE SETTINGS METRIC A/F SOCKET SET & WRENCH M4 BOLT = 8Nm • METRIC HEX KEY BIT SET M5 BOLT = • M6 BOLT = • 28mm HOLE SAW & DRILL M8 BOLT = 20Nm •...
  • Page 3 Page 3 of 8 CP0168 FITTING INSTRUCTIONS Before removing engine bolts, ensure the bike is upright and supported by a suitable engine stand or jack placed under the sump of the motorbike to support the partial weight of the engine, this will prevent the engine from moving during fitting. DO NOT REMOVE MORE THAN 1 ENGINE BOLT AT ANY TIME.
  • Page 4 Page 4 of 8 CP0168 CONSUMER NOTICE The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
  • Page 5 Page 5 of 8 CP0168 NOTICE DE MONTAGE POUR CP0168 PROTECTIONS CRASH E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...
  • Page 6 Page 6 of 8 CP0168 WWW.RG-RACING.COM OUTILS REQUIS VALEURS DE SERRAGE M4 BOULON = 8Nm CLÉ HEXAGONALE • M5 BOULON = 12Nm CLÉ MÉTRIQUE & CLÉ À MOLETTE • M6 BOULON = 15Nm PERCEUSE & SCIE TROU 28mm • M8 BOULON = 20Nm CLÉ...
  • Page 7 Page 7 of 8 CP0168 NOTICE DE MONTAGE Avant de retirer les boulons du moteur, assurez-vous que la moto soit en position verticale et soutenue par un support moteur ou un cric approprié placé sous le carter de la moto pour supporter le poids partiel du moteur, cela empêchera le moteur de bouger pendant le...
  • Page 8 Page 8 of 8 CP0168 • À l'aide d'une clé dynamométrique, serrez le boulon à 40 Nm. Note : Le couple de serrage des boulons du moteur/bobine doit être vérifié à intervalles réguliers lors de l'entretien/réparation de routine. ISSUE 2 - 11/09/2024 (MH) CONSUMER NOTICE The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design...