System Information - Monacor VERT-12 Mode D'emploi

6.1.5 Saving user-defined settings
In VERT-12, up to 5 user-defined settings can
be saved under a user-defined name .
Menu item Setting
To load user-defined settings
LOAD PRESET
previously saved
To save user-defined settings
STORE PRESET
To delete all user-defined
ERASE PRESET
settings
To save the settings, call up the menu item
. A list of storage locations
STORE PRESET
... will be shown . Select and confirm
U1 U5
the storage location desired .
You will be prompted to enter a name, e . g .:
Enter name for U1
Save Clear Cancel
Use the rotary knob to select the input field .
The character ↲ will be shown in the input
field .
1) Press the knob; a frame for the character
to be entered will be shown .
2) Turn the knob to select the character; then
press the knob to confirm the character
selected . The frame will go to the next
character .
3) Repeat step 2 until the complete name
has been entered . An empty frame will be
shown after the name . To exit the input
mode, press the knob again; the character
↲ will be shown .
4) To save the name, select
of the rotary knob; then press the knob
to confirm .
To delete a wrong name, use
enter the correct name .
To cancel the input, use
To load a setting previously saved, call up the
menu item
LOAD PRESET
location ... desired from the list and
U1 U5
then confirm the storage location selected .
To delete all settings saved:
1) Call up the menu item
Confirm Erase:No
(The process could now be canceled by
pressing the knob .)
2) Turn the knob so that
is shown .
Yes
3) Press the knob to confirm the deletion .
10
6.1.6 Bluetooth receiver
Wireless connection of the integrated Blue-
tooth receiver to a Bluetooth source (e . g .
smartphone or tablet computer) is supported
as an alternative or in addition to the replay
of an audio source at the jacks LINE INPUT (8)
of the input CH . D .
1) Call up the menu item
2) Use the rotary knob to select the option
desired and then press the knob to con-
firm .
OFF
ON
TWS
two Bluetooth receivers can be combined
in such a way that each receiver replays
-
only a single stereo channel
3) Activate the Bluetooth function at the
Bluetooth source . In the list of the units
available, VERT-12 will be indicated by the
name "Bluetooth" .
4) Pair the source with "Bluetooth" (refer to
the manual instructions of the Bluetooth
source, if required) . The two units will then
automatically be connected .
When the connection has been estab-
lished, the announcement "Connected"
can be heard .
The replay volume depends on the setting
at the Bluetooth source and on the setting
of the volume control (4) of channel CH . D .
When Bluetooth reception is activated, the
by means
Save
level indication of the display (1) will replace
the indication
Bluetooth symbol . When there is no Blue-
and then
Clear
tooth connection, the symbol will flash rap-
idly; it will flash slowly when the Bluetooth
.
Cancel
connection has been established . The symbol
will not flash when a connection has been
established and the TWS function has been
, select the storage
activated .
Note: When an audio source is connected to the
jacks LINE INPUT (8) during Bluetooth replay, the two
signals will be mixed .
.
ERASE PRESET

6.1.7 System information

will be shown .
To show the version of the DSP firmware, call
up the menu item
Confirm Erase:
6.1.8 Reset
The unit can be reset to its factory settings .
With the reset, all settings the user may have
made will be lost .
1) Call up the menu item
Confirm Reset:No
process could now be canceled by pressing
the knob .)
2) Turn the knob so that
Reset:Yes
3) Press the knob to confirm the reset .
All rights reserved by MONACOR
manual may be reproduced in any form or by any means for any commercial use.
BT ON/OFF
= Bluetooth reception deactivated
= Bluetooth reception activated
= True Wireless Stereo technology:
of the fourth input with the
.
INFO
FACTORY RESET
will be shown (The
Confirm
is shown .
INTERNATIONAL GmbH & Co. KG. No part of this instruction
®
7 Specifications
Amplifier power
Total peak power: � � � � � � � � � � 700 W
Rated power,
low-frequency range: � � � � � � � 300 W at 4 Ω
Rated power,
mid-high frequency range: � � � 180 W at 6 Ω
.
Frequency range: � � � � � � � � � � � � 20 – 20 000 Hz
Speaker system
Low-frequency range: � � � � � � � ⌀ 30 cm (12")
Mid-frequency range (6 ×): � � ⌀ 7�6 cm (3")
High-frequency range: � � � � � � ⌀ 2�5 cm (1")
SPL (1 W/1 m): � � � � � � � � � � � � � 98 dB
Max� SPL: � � � � � � � � � � � � � � � � � 122 dB
Radiation angle
horizontal: � � � � � � � � � � � � � � � 120°
vertical: � � � � � � � � � � � � � � � � � 30°
Input sensitivity / Impedance
CH� A, CH� B (XLR, 6�3 mm jack, bal�)
MIC: � � � � � � � � � � � � � � � � � � 7 mV/10 kΩ
LINE: � � � � � � � � � � � � � � � � � � 400 mV/10 kΩ
CH� C (6�3 mm, unbal�): � � � � � � 50 mV/ 500 kΩ
CH� D (RCA L / R): � � � � � � � � � � � 150 mV/15 kΩ
Pin configuration CH� A, CH� B:
1 Ground
2 1
2 Signal +
3
3 Signal −
Pin configuration CH� C:
S T
Pin configuration LINE LINK, MIX OUTPUT:
1 Ground
1 2
2 Signal +
3
3 Signal −
Equalizer
LOW EQ: � � � � � � � � � � � � � � � � ±12 dB at 70 Hz
MID EQ: � � � � � � � � � � � � � � � � � ±12 dB
HIGH EQ: � � � � � � � � � � � � � � � � ±12 dB at 12 kHz
High pass filter LOW CUT: � � � � 80/100/120/150 Hz
Signal delay (as distance): � � � � � 100 m max�
Power supply: � � � � � � � � � � � � � � 230 V/ 50 Hz
Power consumption: � � � � � � � � � 950 VA max�
Ambient temperature: � � � � � � � 0 – 40 °C
Dimensions (W × H × D in mm)
Basic unit: � � � � � � � � � � � � � � � 359 × 576 × 432
Column elements: � � � � � � � � � 117 × 807 × 124
.
Total height: � � � � � � � � � � � � � � 2�1 m
Weight
Basic unit: � � � � � � � � � � � � � � � 20 kg
Speaker column: � � � � � � � � � � 4�7 kg
Spacer: � � � � � � � � � � � � � � � � � � 3�1 kg
Subject to technical modification .
S Ground
T Signal
at 70 – 12 000 Hz