Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Active Column Speaker System
These instructions are intended for users with
basic knowledge of PA applications . Please
read the instructions carefully prior to opera-
tion and keep them for later reference . All op-
erating elements and connections described
can be found on page 2 .
1 Overview
a Basic unit with bass speaker and mixing
amplifier
b Spacer with speaker system look
c Speaker column for midrange and high-
range frequencies
1 Display to show the input signal levels, the
total volume setting and the setting menu
2 Rotary knob to adjust the total volume
(when the setting menu has not been
called up)
To call up the setting menu, press the
knob .
in the setting menu:
Turn the knob to
– select a menu item
– set a value
– select an option
Press the knob to
– call up a submenu
– call up a function
– confirm an input
3 Switches to select the input sensitivity, one
each for the inputs CH . A and CH . B (5)
MIC microphone level
LINE line level (e . g . CD / MP3 player, mixer)
4 Volume controls, one each for the input
channels CH . A to CH . D
5 Combined XLR / 6 .3 mm jacks, one each
for the input channels CH . A and CH . B to
connect a microphone or an audio source
with line level
6 XLR connections LINE LINK as feed-
through outputs, one each for the inputs
CH . A and CH . B (5)
7 High-impedance instrument input
(6 .3 mm jack)
8 Input LINE INPUT (RCA jacks) to connect
an audio source with line level (e . g . CD /
MP3 player, mixer)
Note: The input is provided with a pair of jacks
for the connection of stereo audio sources . The
amplifier will create a mono signal from the
stereo signal .
8
9 XLR jack MIX OUTPUT PRE DSP to route
the unprocessed mixed signal to another
amplifier system, for example
10 Volume control SUB LEVEL for the bass
speaker to adjust the bass content
11 Mains jack for connection to a mains sock-
et (230 V/ 50 Hz) by means of the mains
cable provided
12 Support for the fuse
Always replace a blown fuse by one of
the same type!
13 Power switch
2 Safety Notes
The product corresponds to all relevant di-
rectives of the EU and is therefore marked
with
.
WARNING The product uses dangerous
mains voltage . Leave servic-
ing to skilled personnel only .
Inexpert handling may result
in electric shock!
•
The product is suitable for indoor use only .
Protect it against dripping water, splash
water and high air humidity . The admissi-
ble ambient temperature range is 0 – 40 °C .
•
Do not place any vessels filled with liquid,
e . g . drinking glasses, on the unit .
•
Do not use the product and immediately
disconnect the mains plug from the mains
socket if
1 . a unit or the mains cable is visibly dam-
aged,
2 . a defect might have occurred after a
unit was dropped or suffered a similar
accident,
3 . malfunctions occur .
In any case the units must be repaired by
skilled personnel .
•
Never pull the mains cable to disconnect
the mains plug from the mains socket, al-
ways seize the plug .
•
For cleaning the product only use a dry,
soft cloth; never use water or chemicals .
•
No guarantee claims for the product and no
liability for any resulting personal damage
or material damage will be accepted if the
product is not correctly used, if it is not set
up safely or if it is not expertly repaired .
If the product is to be put out of
operation definitely, dispose of the
product in accordance with local
regulations .
3 Applications
The active 3-way column speaker system
VERT-12 can be used for a wide range of
PA applications . The individual components
(basic unit, spacer, speaker column) can be
connected so that VERT-12 is ideally suited
for mobile applications . Two class D amplifiers
for the low-frequency range and the mid-high
frequency range are available .
Apart from two microphones, other
audio sources (e . g . CD / MP3 player, mixer,
musical instrument) can be connected to the
four input channels . In addition, it is possi-
ble to receive audio signals via Bluetooth . By
means of the feed-through outputs, the sig-
nals of the first two channels and the mixed
signal of all channels can be routed to another
amplifier system, for example .
For sound adjustment and frequency
splitting, the audio signals pass a digital sig-
nal processor (DSP) which also includes an
adjustable signal delay and a signal limiter to
protect the speakers .
3.1 Conformity and approval
Herewith, MONACOR INTERNATIONAL de-
clare that the product VERT-12 complies with
the directive 2014 / 53 / EU . The EU declaration
of conformity is available on the Internet:
www .monacor .com
The product is generally approved for opera-
tion in EU and EFTA countries; it is licence-free
and requires no registration .
4 Setting up the Unit
Place the basic unit a on an even, horizontal
surface and position it towards the audience .
Connect the spacer b to the upper side of the
basic unit a and then connect the speaker
column c to the spacer b . If the speaker
system is set up at an elevated position (e . g .
on a stage or on a table), it is possible to
connect the speaker column directly to the
basic unit without using the spacer .
Publicité
Table des Matières
