Publicité
8 Press 'Radiator valve Name'. Fill in a preferred name for the device and press 'OK' (Android)
or 'Ready' (iOS).
9 Press 'Code' and then press 'Generate new code'.
A beep sounds , and the smart thermostat head is linked up with HomeWizard.
10 Press the check mark in the upper right of the screen.
The smart thermostat head has been added to the HomeWizard app and is to be found on
the home screen under 'Thermostat head'..
Perform the above steps for the other heating controller. See paragraph 8.7 for adding a remote control.
7.3.2
How do I set the temperature?
1 On the Home screen of the HomeWizard app press 'Thermostat head'. A drop-
down menu appears with the smart thermostat head added by you.
2 Tap on the name of the preferred thermostat head.
A pop-up appears.
3 Move your finger across the screen to choose the correct temperature.
4 Press 'Set' to set the temperature.
7.3.3
How do I enable or disable the smart thermostat head?
1 On the Home screen of the HomeWizard app press 'Thermostat head'. A drop-
down menu appears with the smart thermostat head added by you.
2 Perform one of the following actions:
a. Press the
icon to connect the smart thermostat head to the high adjusted
temperature.
b. Press the
icon to connect the smart thermostat head to the low adjusted
temperature.
7.4 Other HomeWizard applications
You can also use the smart thermostat head in combination with actions, timers and scenes!
1 Actions: if you also linked a thermometer to your HomeWizard, then, in one and the same
action you can also set the thermostat head to switch 'on' by itself when a particular
temperature has been measured.
2 Timers: add a timer to the thermostat head in the HomeWizard app to let it go to a
certain temperature at a desired point in time.
3 Scenes: add several thermostat heads to a 'scene' so that with one press of the button, you
can provide all thermostat heads with the same preferred temperature simultaneously.
8 Maintenance
• The product is maintenance-free, so do not open it. The warranty shall lapse if you open the product.
• Check once a month whether the fixing ring is properly fixed. Bolt the fixing ring tight if it is loose.
• Replace the batteries when the battery indicator begins to flash.
Notice! The memory of the product is saved for 1 minute only.
30 User maual –wireless climate control
All manuals and user guides at all-guides.com
9 Failures
Storing
Information on display
not visible
The battery symbol
flashes
Display shows F1
Display shows F2
Display shows F3
Display shows FULL
10 Warranty
This device has a limited two-year warranty. For the guarantee conditions go to:
www.smartwares.eu.
11 Technical specifications
Required batteries heating controller
(not included):
Required remote control battery:
Measured range:
Setting range:
Measurement accuracy:
Temperature span:
Measured cycle:
Ambient temperature:
Storage temperature:
Humidity:
Power consumption:
Standby power consumption:
Frequency:
Reception range:
Other:
Cause
Oplossing
- Batteries empty
Replace the batteries
- Batteries inserted
Insert the batteries correctly in the product
incorrectly
Batteries are almost
Replace the batteries. Note! The memory of the product is saved for 1
empty
minute only.
The valve is not
Re-install the product on the radiator
responding properly
The valve is too far
Bolt on the fixing ring and ensure that there is less distance between
from the radiator
the radiator and the thermostat head.
Het ventiel zit te dicht
Loosen the ring and ensure that there is more distance between the
op de radiator
radiator and the thermostat head.
The memory is full
Disconnect one external device of the smart thermostat head or
disconnect all external devices of the smart thermostat head
3V DC, 2x 1,5V DC, non-rechargeable
penlight batteries, type AA
12 VDC, 1 x A23
0 ... 29.5°C
5 ... 28°C
+/- 0.5°C
1°C or 2°C adjustable
2 minutes
0 ... 35°C
-20 ... 70°C
5 ... 90% relative
Max. 100 mA
Max. 500 µA
433.92 MHz
Max. 30 m
Use exclusively in
User manual – wireless climate control kit 31
Publicité
