Publicité
3 Press the OK button.
'0.0 °C' appears on the display.
4 Set the preferred offset temperature by turning the dial button.
5 Press OK to confirm.
7.1.9
Resetting to factory settings
1 Keep the Menu button pressed until 'Pro' appears on the display.
2 Choose 'rES' by turning the dial button.
3 Press the OK button.
'rES' flashes on the display.
4 Press OK to reset the thermostat head to the factory settings. Press the Menu
button to cancel.
7.2 Operating the heating control set with remote control
Using the remote control the heating can be set to a high or low temperature. To this end, the
smart thermostat head needs first to be set on a high
information, see sub-section 6.1.3.
The range of a remote control is 50 metres, which means that you can easily enable the smart
thermostat head from the other side of the house.
7.2.1
Setting a high or a low temperature
Notice! The smart thermostat head can be connected to up to 3 wireless devices
(such as the HomeWizard, a remote control or a sensor). When the memory is full,
(FULL) appears on the display. Refer to Chapter 9 for more information.
1 Keep the Menu button pressed until 'Pro' appears on the display.
2 Choose 'rFS' by turning the dial button.
Notice! Make sure that you choose 'rFS' and not 'rES'. When you chose 'rES' and follow
the steps below, you reset the smart thermostat head to the factory settings.
3 Press the OK button.
The smart thermostat head arrives in the coupling position. Within 30 seconds a
remote control can be coupled or decoupled.
4 Perform one of the following actions:
a. Press one of the ON buttons to couple the remote control. When a beep
sounds, the remote control has been coupled.
b. Press one of the OFF buttons to decouple the remote control. When a beep
sounds, the remote control has been decoupled.
c. Press the ALL OFF button to disconnect all remote controls. When a beep
sounds, all remote controls have been decoupled.
28 User maual –wireless climate control
All manuals and user guides at all-guides.com
and low
temperature. For more
7.2.2
Operate the smart thermostat head with a remote control
1 Set the preferred smart thermostat head to a high and low temperature. See sub-section
7.1.3 for more information.
2 Perform one of the following actions:
3 Press the ON button to connect the smart thermostat head to the high adjusted
temperature.
4 Press the OFF button to connect the smart thermostat head to the low adjusted
temperature.
7.2.3
Disconnect all remote control devices via the smart thermostat head
1 Keep the Menu button pressed until 'Pro' appears on the display.
2 Choose 'UnL' by turning the dial button.
3 Press the OK button.
'UnL' flashes on the display.
4 Press OK to disconnect all paired remote control devices. Press the Menu button to canceln.
Notice! This device is compatible with HomeWizard. HomeWizard enables you to operate
this device with an app on your Smartphone or tablet. For more information about
HomeWizard visit the website www.HomeWizard.com.
7.3 Operating the heating control set with Homewizard
7.3.1
How do I add the smart thermostat head to the HomeWizard app?
Notice! The smart thermostat head can be linked to up to 3 external devices. When the
memory is full, (FULL) appears on the display. Refer to Chapter 9 for more information.
1 Open the HomeWizard app on your
Smartphone or tablet.
2 Keep the Menu button pressed
until 'Pro' appears on the display.
3 Choose 'rFS' by turning the dial button.
Notice! Make sure that you choose 'rFS' and not 'rES'. When you chose 'rES' and follow
the steps below, you reset the smart thermostat head to the factory setting
4 Press the OK button.
The smart thermostat head waits in the coupling position. Within 30 seconds the smart
thermostat head can be linked-up with the HomeWizard app.
5 On the upper left corner of the screen, press the 'Menu' button (the three lines above each
other). The menu appears.
6 Press 'New Sensor'.
Tip! Move your finger across the screen to search.
7 Press 'Thermostatic head'.
User manual – wireless climate control kit 29
Publicité
