EINHELL 34.113.20 Instructions D'origine page 26

The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long
service, you should take care to recharge it
promptly. You must recharge the battery pack
when you notice that the power of the cordless
grass trimmer drops. Never allow the battery pack
to become fully discharged. This will cause it to
develop a defect.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
5.12 Battery capacity indicator (Fig. 15)
Press the button for the battery capacity indicator
(Item H). The battery capacity indicator (Item F)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
Anl_Agillo_36_255_BL_SPK13.indb 26 Anl_Agillo_36_255_BL_SPK13.indb 26
GB
6. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
Danger! The guard hood must be fi tted when
carrying out work.
6.1 Switching the equipment on and off , ad-
justing the speed (Fig. 16)
Switching on and setting the speed
Press the safety lock-off (3) and press the On/Off
switch (2) at the same time. Adjust the speed du-
ring operation by pressing the On/Off switch to a
greater or lesser extent. The harder you push, the
higher the speed.
Switching off
Release the On/Off switch.
6.2 Practical tips
Practice all the work steps with the motor swit-
ched off and without the rechargeable battery be-
fore you start to use the equipment. Only use the
cutting line to mow grass that is dry. If the grass
is long, the grass must be cut shorter in stages
(Fig. 17).
Extending the cutting line (Fig. 18)
Danger! Do not use any kind of metal wire or me-
tal wire encased in plastic in the line spool. This
may cause serious injuries to the user.
The grass trimmer has a semi-automatic line
extension system (automatic jog line feed). Each
time you activate the semi-automatic line exten-
sion system, the line is automatically extended to
ensure that you can cut your lawn with the perfect
cutting width at all times. To extend the cutting
line, run the motor and tap the line spool on the
ground. This will automatically extend the line.
The blade on the guard hood will cut the line to
the permissible length. Please note that the more
often you activate the semi-automatic line exten-
sion system, the more the line will wear.
Note: If the line is too long when you use the
equipment for the fi rst time, the surplus end of it
will be cut by the blade on the guard hood. If the
line is too short when you start the equipment
for the fi rst time, press the knob on the line spool
and pull the line hard. When you then start the
- 26 -
03.11.2021 13:41:54 03.11.2021 13:41:54