Publicité
USING THE CONTROL PANEL
PROGRAMS:
(START/STOP) BUTTON
Press Start/Stop button once to activate the 30-second blend cycle.
POWER BUTTON
Press Power button to turn unit ON and OFF.
LED Color(s)
Troubleshooting
Flashing WHITE
Vessel and base are not aligned
Flashing ORANGE
Blades are blocked
Solid RED
Needs charge
Flashing RED and BLUE
Abnormal charger
Clockwise-moving ORANGE
Unit cool-down time-out
Flashing WHITE and RED
While charging
Flashing RED in the bottom left
While blending
and top right
USING THE BLENDING VESSEL
IMPORTANT: Review all warnings at the beginning of this Owner's Guide before proceeding.
1
Ensure the motor base is fully charged, and ensure the vessel is properly
installed by aligning vessel arrow with motor base arrow located on the back
of the motor base.
2 Turn unit ON by pressing the
lights illuminate.
3 Add ingredients, starting with liquids, to the MIN LIQUID line.
Then add solid ingredients. If using ice, always add it last. DO NOT
fill ingredients past the MAX FILL line. Secure lid onto the vessel,
twisting clockwise to tighten.
4 Blend for a 30-second blend cycle by pressing the
ninjakitchen.ca
Solutions
Ensure vessel and motor base are
aligned using the arrows on the vessel
and the back of motor base.
Move lodged ingredients from blades
and restart blending program.
Charge unit.
Defective charger; unplug and find
correct 5V 3A charger.
Let unit sit at room temp for 15 minutes
before using again.
Call Customer Service.
Call Customer Service.
button until
(Start/Stop) button
(Start/Stop) button.
5 Open the sip lid to sip, or remove the lid to pour out blender outputs into another container.
DO NOT remove vessel from motor base when filled. Empty vessel prior to removing from
motor base.
6 After blending, power OFF the unit by pressing the
turned OFF when drinking from the sip lid and when blender is no longer in use.
7 After blending is complete, ensure the lid is on tight and turn the
blender upside down.
8 Twist motor base counterclockwise to remove it from the vessel,
and set the motor base right side up.
9 Install the vessel cap on the bottom of the vessel by turning it clockwise. Install the blade
cover on the motor base to cover the exposed blades of the motor base by turning the
cover clockwise.
10 Refer to the Care & Maintenance section for cleaning and storage instructions.
CARE & MAINTENANCE
CLEANING
Blades can still operate when the lid is removed. Always turn the unit OFF when cleaning without the lid on
or when the BlastBlade™ Assembly is exposed.
Quick Clean
To clean, add warm water up to MIN LIQUID line, then add 1 small drop of dish soap. Securely attach the
lid and blend. Empty contents and rinse again with warm water.
Hand-Washing
Wash vessel, lid, and BlastBlade™ Assembly with warm, soapy water. Use a dishwashing utensil or cloth
to clean the BlastBlade™ Assembly on the motor base. Exercise care when handling the BlastBlade™
Assembly on the motor base as the blades are sharp. Wipe the motor base with a clean, damp cloth.
DO NOT submerge the motor base in water. Thoroughly rinse and air-dry all appropriate parts.
Motor Base
Motor base is NOT dishwasher safe and cannot be submerged in water. Use a long-handled cleaning brush
to clean the blades. DO NOT put the motor base in the dishwasher or submerge in water. Ensure the
USB-C charger is not inserted before cleaning. Use the USB-C cover over the charging port when cleaning
(feature not on all models). After cleaning, let the USB-C charging port air-dry for 30 minutes before
charging the unit.
DEEPER CLEAN
Dishwasher
Vessel, sip lid, and covers are top-rack dishwasher safe. DO NOT use a heated dry cycle. Ensure the
vessel and sip lid are removed from the motor base before being placed in the dishwasher. After
cleaning, let the USB-C charging port air-dry for 30 minutes before charging the unit.
STORING
Store the unit upright and with the lid, vessel, and motor base fully assembled.
DO NOT store blended or unblended ingredients in the vessel with the BlastBlade™ Assembly attached
for prolonged periods of time.
DO NOT stack items on top of the vessel. Store any remaining attachments alongside the unit
or in a cabinet where they will not be damaged or create a hazard.
If your unit needs servicing, call Customer Service at 1-877-646-5288. So we may better assist you, please
register your product online at registeryourninja.com and have the product on hand when you call.
button. Motor base should be
ninjakitchen.ca
Publicité
