Publicité
Troubleshooting
Often, what appears to be a malfunction is due to user error. Before calling for service, please consult the following table.
Problem
Power cannot be
turned on (illumina-
tion does not light).
No sound
Sound is small.
Sound quality is bad
(sound is distorted).
Sound is unnatural.
Remote control does
not work.
The illuminations on
the remote control
unit do not light.
Specifi cations
Design and specifi cations are subject to change without notice.
Maximum output ............................................................. 250 W
Frequency response ............................................ 35 Hz–150 Hz
Cut-off frequency ................................................. 50 Hz–125 Hz
Phase ................................................................................0˚, 180˚
Input sensitivity / impedance
LINE IN ............................................................ 125 mV / 22 kΩ
8
English
Cause
• The fuse is blown.
• The power supply pin (yellow) of the 10-pin con-
nection cord is not connected.
• The power control pin (blue/white) of the 10-pin
connection cord is not connected.
• The grounding pin (black) of the 10-pin connec-
tion cord is not connected.
• The 10-pin connector is not plugged in completely.
• The negative ⊖ cable of the car battery is discon-
nected.
• The attenuator of the audio components is set to
ON.
• The VOLUME control is set to the MIN position.
• The speaker cords are connected improperly.
• Connection terminals are connected improperly.
• The input level is set to low.
• Connection terminals are connected improperly.
• Large power input causes the protection circuit
for this unit to operate.
• The input level is set to high.
• The speaker cords are connected with incorrect
positive ⊕/negative ⊖ polarity.
• The grounding pin (black) of the 10-pin connec-
tion cord is poorly contacted.
• The remote control cord is unplugged.
• Check the ⊕/⊖ polarity of the power cord and
that the cords are not shorted, then replace with
a fuse with the rated capacity.
• Re-connect the cords correctly by referring to
the connection example (on page 4, 5).
• Connect the cord correctly by referring to the
connection example (on page 4, 5).
• Attach the grounding terminal to the metallic
section of the vehicle (not a coated surface) by
tightly screwing it.
• Insert the connector all the way in.
• Check the connections of all cords, then connect
the ⊖ cable to the battery.
• Check the connections of all cords, then connect
the ⊖ cable to the battery.
• Switch the attenuator OFF.
• Increase the volume to an optimum level (on
page 7).
• Connect the cords correctly by referring to the
connection example (on page 4).
• Insert the connectors or jacks all the way in to
the terminals.
• Turn the VOLUME control knob and set the input
level to an optimum level.
• Plug the cord into the REMOTE terminal.
• Check that the RCA cord is connected properly.
• Turn the volume to MIN for a while.
• Turn the VOLUME control knob and set the input
level to an optimum level.
• Connect the cords correctly by referring to the
connection example (on page 4, 5).
• Attach the grounding terminal to the metallic
section of the vehicle (not a coated surface) by
tightly screwing it.
• Plug the cord into the REMOTE terminal.
• Insert the connector all the way in.
Power ....................... DC 14.4 V (Operating voltage 11 V–16 V)
Current consumption ..........................................................10 A
Sensitivity .......................................................................... 81 dB
Dimensions ....................................... Width : 350 mm (13-3/4")
Weight ................................................................... 4.5 kg (9.9 Ib)
Remedy
Height : 75 mm (2-15/16")
Depth : 240 mm (9-7/16")
Publicité
