Makita LS002G Manuel D'instruction page 23

Masquer les pouces Voir aussi pour LS002G:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

When cutting, place the workpiece flat against the guide fences.
► 1. Guide fence 2. Sub base
OPERATION
This tool is intended to cut wood products. With appropriate Makita
genuine saw blades, following materials can also be sawed :
Aluminum products
Refer to our website or contact your local Makita dealer for the
correct circular saw blades to be used for the material to be cut.
WARNING:
Make sure the circular saw blade
is not contacting the workpiece, etc. before the
switch is turned on. Turning the tool on with the
circular saw blade in contact with the workpiece may
result in kickback and serious personal injury.
WARNING:
After a cutting operation, do not
raise the circular saw blade until it has come to a
complete stop. The raising of a coasting blade may result
in serious personal injury and damage to the workpiece.
WARNING:
Do not perform any adjustment such
as turning grip, levers, stopper pin on the tool while the
circular saw blade is rotating. Adjustment while the circular
saw blade is rotating may result in serious personal injury.
NOTICE:
Before use, be sure to unlock the stop-
per pin and release the handle from the lowered
position.
NOTICE:
Do not apply excessive pressure on the
handle when cutting. Too much force may result in
overload of the motor and/or decreased cutting effi-
ciency. Press down handle with only as much force as
necessary for smooth cutting and without significant
decrease in blade speed.
NOTICE:
Gently press down the handle to per-
form the cut. If the handle is pressed down with force
or if lateral force is applied, the circular saw blade
may vibrate and leave a mark (saw mark) in the work-
piece and the precision of the cut may be impaired.
NOTICE:
During a slide cut, gently push the car-
riage toward the guide fences without stopping. If
the carriage movement stops during the cut, a mark
may be left in the workpiece and the precision of the
cut may be impaired.
Press cutting
WARNING:
of the carriage when performing a press cutting.
Cutting without lock may cause possible kickback
which may result in serious personal injury.
1
Workpieces up to 70 mm (2-3/4") high and 92 mm
(3-5/8") wide can be cut in the following manner.
1.
Push the carriage toward the guide fences until it
stops and lock it with the stopper pin.
2.
Secure the workpiece with the proper type of vise.
3.
Switch on the tool without the circular saw blade
2
making any contact and wait until the circular saw blade
attains full speed before lowering.
4.
Gently lower the handle to the fully lowered posi-
tion to cut the workpiece.
5.
When the cut is completed, switch off the tool and wait until
the circular saw blade has come to a complete stop before
returning the circular saw blade to its fully elevated position.
1
► 1. Stopper pin
Slide (push) cutting (cutting wide
workpieces)
WARNING:
first pull the carriage full towards you and press
the handle all the way down, then push the car-
riage toward the guide fence. Never start the cut
with the carriage not pulled fully toward you. If
you perform the slide cut without the carriage pulled
fully toward you, unexpected kickback may occur and
serious personal injury may result.
WARNING:
by pulling the carriage towards you. Pulling the car-
riage towards you while cutting may cause unexpected
kickback resulting in possible serious personal injury.
WARNING:
the handle locked in the lowered position.
1.
Unlock the stopper pins so that the carriage can
be elevated and slid freely.
2.
Secure the workpiece with the proper type of vise.
3.
Pull the carriage toward you fully.
4.
Switch on the tool without the circular saw blade
making any contact and wait until the circular saw blade
attains full speed.
23 ENGLISH
Always lock the sliding movement
Whenever performing a slide cut,
Never attempt to perform a slide cut
Never perform the slide cut with

Publicité

Table des Matières
loading

Table des Matières