Milwaukee 2521-20 Manuel De L'utilisateur page 8

To maintain control of the saw during plunge cutting,
keep both hands on the saw.
1. Beginning at a corner, line up the sight line with
your cutting line. Tilt the saw forward, firmly fixing
the front of the shoe on the workpiece. The blade
should be just above cutting line, but not touching
it. Raise the lower guard using the lower guard
lever.
2. To start the saw, push the lock-off button down
while pulling the trigger. Allow the motor to reach
full speed before beginning cut. Using the front
of the shoe as a hinge point, gradually lower the
back end of the saw into the workpiece. Release
the lower guard lever and grasp the front handle.
3. When the shoe rests flat against workpiece,
advance the saw to the far corner. Release the
trigger and allow the blade to come to a complete
stop before removing it from workpiece. Repeat
the above steps for each side of the opening. Use
a Sawzall reciprocating saw, jig saw or small hand
®
saw to finish the corners if they are not completely
cut through.
Overloading
Continuous overloading may cause permanent dam-
age to tool or battery pack.
Cutting Masonry and Metal
MILWAUKEE circular saws are not intended for con-
tinuous use in cutting metal or masonry. When cutting
these materials, use the correct blade. MILWAUKEE
does not recommend using bonded abrasive wheels
on circular saws for any application.
Dust, chips, and grit can cause
WARNING
guard to hang up at any time. If saw
is used to cut masonry or metal, reserve and mark
it for that purpose only and return it to a
MILWAUKEE service facility for cleaning and
testing before using it for wood cutting.
Only use accessories with maximum speed rating
at least as high as nameplate RPM of tool.
When cutting masonry, use a diamond blade. Make
successive passes at depths of less than 1/4" to
achieve the desired depth. Cutting at a depth of more
than 1/4" will damage wheel. Remove battery pack
and frequently clean dust from air vents and guards.
Do not use tool for cutting metal
WARNING
near flammable material. Sparks
may cause fire.
When cutting metal, use a metal cutting blade. Set
depth of cut to full depth. Protect everyone in the
area from sparks.
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the battery pack, charger, or tool, except as pro-
vided in these instructions. Contact a MILWAUKEE
service facility for all other repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from any vents. Keep tool
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.
ACCESSORIES
Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
8
Cleaning
Repairs