CAT MATE Elite 305 Mode D'emploi page 6

9.5 Setting Timer Control/Clock for ALL Cats
If you wish to set your cat flap to ensure that ALL cats have a particular access option,
over a selected timed period, e.g. to keep your cat(s) in at night between 19:00 and
06:00, you will first need to decide:
a) Which lock setting should apply DURING the timed period, (in the above example
'IN ONLY' will apply). Outside the timed period, the lock setting made in 9.1 to 9.3
will apply.
b) When the timed period should 'START' (In the above example 19:00hrs).
c) When the timed period should 'FINISH' (in the above example 06:00hrs).
d) You will also need to know the current time.
Proceed as follows:
NOTE: if you do not press a button for more than 60 seconds the display will revert to
normal and you will need to start again.
9.5.1 Press the 'TIMER' button for 5 seconds until the Timer function indicator
flashes.
9.5.2 Repeatedly press the '4 WAY' button to select the required access options
from: 'IN & OUT', 'IN ONLY', 'OUT ONLY', 'LOCKED' or 'OFF'.
9.5.3 Press the 'PROG' button to save the setting.
9.5.4 The display will show time with the Minute symbol flashing. Repeatedly press
the '+' button until the current Minutes setting is shown (i.e. 10 if the current
time is 12:10).
9.5.5 Press the 'PROG' button to save the setting.
9.5.6 The display will now show the time with the Hour symbol flashing.
If you wish to change between a 24 hour clock and AM/PM setting, press the
'TIMER' button.
9.5.7. Repeatedly press the '+' until the correct Hour setting is shown (e.g. 12 if the
current time is 12:10).
9.5.8. Press the 'PROG' button to save the setting.
9.5.9. The display will show the word 'START' and the minutes will flash. Press the '+'
button until the desired minutes setting is shown, (in the above example '00').
Press the 'PROG' button to save the setting.
9.5.10 Then set the hours in the same way (in the above example 19:00).
9.5.11 The display will show the 'FINISH' time. Set in the same way as the 'START'
time. Remember to press 'PROG' to save the setting.
When the Timer is set, the Timer function indicator ( 6 , Fig. 1) will be shown on the
display.
When the timed lock is active, the access option symbol chosen at 9.2 will flash slowly.
To check the time settings, briefly press the 'TIMER' button and release. The display
will show the timed access option selected and the 'START' time. Press the 'TIMER'
button again to show 'FINISH' time. The display will revert to current time after 5
seconds.
10
To cancel timer control and revert back to the normal access option:
9.5.12 Press the 'TIMER' button for 5 seconds.
9.5.13 Press the '4 WAY' button and go back through the options until you come to
'OFF'.
9.5.14 Press the 'PROG' button 3 times to keep the current clock time and return to
the normal display.
10. Battery Replacement
When the low battery indicator ( 4 , Fig. 1) comes on, alkaline batteries should be
replaced. (See Section 2).
Please note, after fitting new batteries:
• Low battery indicator may remain on for up to 15 minutes.
• Flap will remember all microchip(s) and I.D. Disc(s), Lock Settings and Lock Times
but CURRENT TIME WILL NEED RESETTING. (See section 9.5).
11. Reprogramming an I.D Disc
11.1 Press the 'PROG' button for 5 seconds, the next unused Cat number will flash
and there will be lines moving around the first 'TWO ZEROS'.
11.2 Press the '+' button to select the appropriate Cat number you wish to reprogram
or select the next available Cat number. (A 'P' next to the Cat number indicates
that it has already been programmed, although you may reprogram as follows).
11.3 Place the front of the I.D. Disc up against the flap (Fig. 4).
11.4 When programmed, the 'TWO ZEROS' will disappear and 'Pr' will flash.
11.5 Press the 'PROG' button to save the setting.
For additional cats, up to a maximum of 9, repeat steps 11.1 to 11.5.
12. Factory Reset
To reset the cat flap back to the setting when you first bought it, press and hold the '+'
button for about 30 seconds until all symbols show on LCD. After a period of self
checking, the 'IN & OUT' symbol will be all that is visible on the LCD display. This
procedure will erase all I.D. Disc(s) and all other settings. You will then need to re-
program the I.D. Disc(s) (See Section 3).
13. High Security Mode
This cat flap is supplied with high security mode enabled ('Eon') to ensure no
unwanted entry by other cats or raccoons.
If your cat still has difficulty using the cat flap after successfully using training mode,
you may wish to disable high security mode ('EOFF') temporarily or permanently to
enable easier entry/exit by your cat.
You can disable high security mode as follows:
13.1 Press and hold 'PROG' button and within 3 seconds briefly press the '+' button.
When the display shows 'Eon' (high security mode enabled) release the 'PROG'
button.
13.2 You may toggle between 'Eon' and 'EOFF' by pressing the '4 WAY' button. Press
'PROG' to save the desired setting.
11