Publicité
Connection
AnschluB
Raccordement
Aansluiting
Conexion
Collegamento
Ansluiting
Tilslutning
Liitanta
Black
Press
Schwarz
Drúken
Noir
Appuyer
Zwart
Indrukken
Negro
Presionar
Nero
Premere
Svart
Tryck
Sort
Tryk
Musta
Paina
—
. Remove the ending part of the vinyl covering from the cut.
Twist the wires.
1. Entfernen Sie dan Endstúck der Vinylhúle von dem geschnittenen
ech
N
=
M —
Teil.
. Drehen Sie die Kabel.
. Enlever la pertie d'extrémité du recouvrement vinylique de la partie
déoupée.
. Tordre les fils.
Snijd het laatste gedeelte van de vinylmantel af en verwijder.
Draai de draadkernen ineen.
. Quitar la parte de la extremidad de la cubierta de plastico de la
parte cortada.
. Torcer los alambres.
1. Rimuovete l'estremita della copertura in plastica dalla parte
N=
N
N —+
hw
tagliata.
Torcete | fili.
Dra loss den avskurna delen av isoleringen frän kabeländen.
Tvinna trädarna.
Fjern enden af vinyl-isoleringen, hvor den er klippet af.
Sno trädene.
Irrota muovipeitteen loppupää uurteesta.
Kierrä johdot.
CONNECTION
e Connect the LEFT speaker terminals of the amplifier to the
LEFT terminals of the speaker and RIGHT to RIGHT using
the attached speaker cords as shown in the figure making
sure polarity is correct; (+) to (+) and (-) to (-). Connect the
black speaker wire to the (—) terminal.
e Turn off power to the whole system before connecting the
speakers to the amplifier.
e The nominal impedance of the SX-F300WD is 8 O. Select for
use an amplifier to which a speaker system with the load im-
pedance of 8 (2 can be connected.
e The maximum power handling capacity of the SX-F300WD is
150 W. Excessive input will result in abnormal noise and pos-
sible damage. In cases where the signals described below
are applied to the speakers, even if the signals are below the
maximum allowable input, they may cause an overload and
burn the wiring of the speakers. Be sure to lower the amplifier
volume beforehand.
1) Noise during FM tuning.
2) High level signals containing high frequency components
produced by a tape deck in the fast forward mode.
3) Click noise produced when turning power of other compo-
nents on and off.
4) Click noise produced when connecting or disconnecting
cords with the power on.
5) Click noise produced when the cartridge is replaced with
the power on.
6) Click noise produced when operating amplifier switches.
7) Continuous high frequency oscillation or high pitch electroni-
cally produced musical instrument sound.
8) Howling when using a microphones.
SPECIFICATIONS
Type
Speakers
Woofer
Midrange
Tweeter
Power Handling Capacity
Impedance
Frequency Range
Sound Pressure Level
Dimensions (W x H x D)
Mass
Accessories
: 3-way bass-reflex type
(Magnetically-shielded type)
: 16.5 cm (6-1/2 in.) cone x 1
:8.0 cm (3-3/16 in.) cone x 1
: 3.0 cm (1-3/16 in.) dome x 1
: 150 W
BL
: 30 Hz — 20 000 Hz
:89 dB/W-m
'225 mm
x 853 mm
x 254 mm
(8-7/8 in. x 33 x 5/8 in. x 10 in.)
: 8.5 ke (18.8 Ibs) each
: Speaker cord.
2
3.0 m (9.84 ft)
Design and specifications subject to change without notice.
Publicité
