MSW -BG-655 Manuel D'utilisation page 4

TECHNICAL DATA
Parameter description Parameter value
Product name Fender Reforming Tool
Model MSW-BG-655
Maximum length [mm] 570
Minimum length [mm] 370
Range of adjustment [mm] 140
Inside diameter [mm] 73
Outside diameter [mm] 150
Weight [kg] 6,54
1. GENERAL DESCRIPTION
The user manual is designed to assist in the safe and
trouble-free use of the device. The product is designed
and manufactured in accordance with strict technical
guidelines, using state-of-the-art technologies
components. Additionally, it is produced in compliance
with the most stringent quality standards.
DO NOT USE THE DEVICE UNLESS YOU HAVE
THOROUGHLY READ AND UNDERSTOOD THIS
USER MANUAL.
To increase the product life of the device and to ensure
a trouble-free operation, use it in accordance with this user
manual and regularly perform the maintenance tasks. The
technical data and specifications in this user manual are
up to date. The manufacturer reserves the right to make
changes associated with quality improvement.
Legend
Read instructions before use.
WARNING! or CAUTION! or REMEMBER!
Applicable to the given situation (general warning
sign).
Wear protective gloves.
ATTENTION! Danger of hand crushing.
PLEASE NOTE! Drawings in this manual are for
illustration purposes only and in some details it may
differ from the actual product.
The original operation manual is in German. Other
language versions are translations from German.
2. USAGE SAFETY
ATTENTION! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in serious injury or even
death.
Whenever "device" or "product" are used in the warnings
and instructions, it shall mean Fender Reforming Tool.
2.1. SAFETY AT THE WORKPLACE
a) Make sure the workplace is orderly and well lit.
A messy or poorly lit workplace may lead to accidents.
Try to anticipate what may happen, observe what is
6
U S E R M A N U A L
going on and use common sense when working with
the device.
b) Upon discovering damage or irregular operation,
immediately switch the device off and report it to
a supervisor without delay.
c) If there are any doubts as to the correct operation
of the device, contact the manufacturer's support
service.
d) Only the manufacturer's service point may repair the
device. Do not attempt any repairs independently!
e) Children or unauthorised persons are forbidden from
entering a work station (a distraction may result in
a loss of control over the device).
REMEMBER! When using the device, protect
children and other bystanders.
2.2. PERSONAL SAFETY
a) Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
b) The machine may be operated by physically fit
and
persons who are able to handle the machine and
properly trained and who reviewed this operating
manual and received training in occupational health
and safety.
c) The device is not designed to be handled by persons
(including children) with limited mental and sensory
functions or persons lacking relevant experience and/
or knowledge unless they are supervised by a person
responsible for their safety or they have received
instructions on how to operate the device.
d) When working with the device, use common sense
and stay alert. Temporary loss of concentration whilst
using the device may lead to serious injuries.
e) Use personal protection equipment as required
for working with the device, specified in section 1
(Legend). The use of correct, approved personal
protection equipment reduces the risk of suffering an
injury.
f) Do not overestimate your abilities. When using the
device keep your balance and remain stable at all
times. This will ensure better control over the device
in unexpected situations.
2.3. SAFE DEVICE USE
a) Do not overload the device. Use appropriate tools for
the given task. A correctly selected device will perform
the task for which it was designed better and in a safer
manner.
b) When not in use, store in a safe place, away from
children and people not familiar with the device, who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
c) Maintain the device in a good technical state. Before
each use check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of the
device. If damage is discovered, hand over the device
for repair before use.
d) Keep the device out of the reach of children.
e) Device repair or maintenance should be carried out by
qualified persons, only using original spare parts. This
will ensure safe use.
f) Clean the device regularly to avoid a durable
encrustation of dirt.
Rev. 27.09.2018
g) Exercise special care during device assembly on /
disassembly from the vehicle. The device can fall if it
is installed improperly or without any support during
assembly / disassembly.
h) Do not exert too much pressure with the device. This
can result in damage of the vehicle or the device itself.
i) Exercise care when using the device. Your hand can
be crushed between the roll and the fender during
adjustment and device operation. Use the protective
gloves.
ATTENTION! Despite the safe design of the device
and its protection facilities and despite the use of
additional elements protecting the operator, there is
still a slight risk of an accident or injury when using
the device. When using the device stay alert and use
common sense.
3. USE GUIDELINES
The Fender Reforming Tool is designed to shape car fenders,
i.e. to remove deformations and to increase the space under
the fender for car wheels.
The user is liable for any damage resulting from
nonintended use of the device.
3.1. DEVICE DESCRIPTION
6
5
13
11
4
7
1
14
12
3
9
Names of individual elements are listed in the assembly
drawing table at the end of the instructions.
3.2. PREPARING FOR USE
Assembly of the device:
a) Attach the arm body (12) to the fastening ring (1)
using the pin (3).
b) Screw the threaded roller (4) into the leading roller (7)
so as the threaded roller end goes also through the
connecting roller (9). Secure the connection by means
of the nut (10) and washer (8).
c) Unscrew the lever knob (6) and remove the nuts
stored on it.
d) Insert the lever (5) into the hole in the threaded roller
(4). Screw the knob (6) onto the lever (5).
e) Insert the adjustable arm (13) in the arm body (12).
f) Secure the connection using the clamping screw (11).
3.3. DEVICE USE
a) Lift the car using a suitable device (eg. a jack or a car
elevator).
b) Unscrew and remove a car wheel.
c) Fasten the device instead of the car wheel using the
fastening ring (1). Secure the connection by means of
nuts and washers.
Rev. 27.09.2018
e
d
g
f
19
d) Place the device roll (19) in parallel to the device arm
(12). Adjust using the locking screw (14).
e) By means of the lever (4), raise the roll (19) towards
the fender and move the device arm asunder while
pressing it slightly.
f) Shape the fender gradually and, from time to time,
adjust roll (19) pressure on the fender using the lever
(4).
g) Adjust distance of the roll (19) from the adjustment
ring (1) using the clamping screw (11) and the
adjustable arm (13) depending on the fender shape.
3.4. CLEANING AND MAINTENANCE
• Use cleaners without corrosive substances to clean
each surface.
• After cleaning the device, all parts should be dried
before reusing it.
• Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
• Regular inspections of the device must be carried out
in terms of its technical efficiency and any damages
• Grease the movable elements regularly depending on
frequency of their use.
ASSEMBLY DRAWINGS
ATTENTION! This product's exploded view can be
found on the last page of the operating instructions
(pp. 24).
7