Craftsman CMEPW1800 Guide D'utilisation page 6

English
Pressure of Inlet Water*
Inlet Water
Soap Consumption Rate
*Water flow and maximum pressure ratings determined in accordance with
CETA CPC-100.
Attaching Spray Wand (Fig. B)
To connect the spray wand
the end of the spray wand inside the spray handle and turn
the spray wand counterclockwise to lock it into position.
Attaching High Pressure Hose (Fig. C, D)
NOTICE: Never pull high pressure hose to move pressure
washer. This could damage hose and/or pump outlet.
To connect the high pressure hose
handle 4 , screw the hose collar
inlet coupler 21 .
To connect the high pressure hose to the pressure washer
unit 8 , screw the hose collar
water outlet .
17
Attaching Garden Hose (Fig. A, D)
To connect a garden hose to the pressure washer
unit , place the end of the garden hose inside the water
8
intake 18 . Tighten the garden hose by hand.
Always disconnect the garden hose after usage.
nOTE: Before connecting the garden hose to the pressure
washer unit, run water through the garden hose for
thirty seconds to clear any debris from the mouth of the
garden hose.
Attaching Nozzles (Fig. A, E)

DANGER: Risk of fluid injection. Do not direct discharge
stream toward persons, unprotected skin, eyes or any pets or
animals. Serious injury will occur.

WARNING: Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while pressure
washer is running. Turn pressure washer unit OFF before
changing nozzles.
To connect the 40 ° white nozzle
nozzle 15 to the spray wand
collar toward the spray wand and insert the appropriate
3
nozzle. Release the quick connect collar to lock the nozzle
in place.
To ensure nozzle is locked into place, give the nozzle a firm
tug after the quick connect collar has locked into place.
Spray Tip Application
40 ° White Nozzle For gentle wide area cleaning.
Black Turbo Nozzle For abrasive cleaning.
Attaching High Pressure Foam Cannon (Fig. F)
1. To connect the high pressure foam cannon
spray wand 2 , pull the quick connect collar
spray wand and insert the soap bottle.
2. Release the quick connect collar
pressure foam cannon 13
3. Give the high pressure foam cannon
the quick connect collar has locked into place to ensure the
high pressure foam cannon
6
20–100 PSI
Cold Tap
10% MAX
2 to the spray handle 4
to the spray
1
22 onto the spray handle
22 onto the high pressure
16 or the black turbo
2 , pull the quick connect
to the
13
3 toward the
3 to lock the high
in place.
13 a firm tug after
is locked into place.
13
4. To adjust the rate of foam, rotate the pressure
control knob
cannon 13 counterclockwise for less or clockwise for
more foam.
nOTE: The soap bottle should be positioned underneath
the spray wand. Do not position the high pressure
foam cannon above the spray wand as this will lead to
soap dripping on the spray wand. The spray tip on the
high pressure foam cannon
horizontal application.
, insert
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power source
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.
Proper Hand Position (Fig. G)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the spray handle
grip 5 . Hold the spray handle
Test Ground-Fault Circuit Interrupter (GFCI) Before
Each Use
This pressure washer is provided with a ground-fault circuit
interrupter (GFCI) built into the plug of the power supply
cord. This device provides additional protection from the
risk of electric shock.
1. Plug the ground-fault circuit interrupter (GFCI) into a
working grounded outlet.
2. The indicator at the top of the GFCI should turn green
when product is ready to use.
3. Press the "TEST" button (bottom). The green indicator
should disappear.
4. Press "RESET" button for use. Do not use if the above
test fails.
Pressure Washing
Preparing Surface for Cleaning
• Remove objects from the area which could create a
hazard such as children's toys or outdoor furniture.
• Ensure that all doors and windows are closed tight.
Protect all plants and trees in the adjacent area with a drop
cloth ensuring that they will not be harmed by
any overspray.
• Pre-rinse cleaning area with fresh water.
• Use only detergents formulated for pressure washers.
• Always test detergent in an inconspicuous area
before use.
Preparing Pressure Washer Unit for Use
(Fig. A)

DANGER: Risk of fluid injection and laceration. When
using the high-pressure setting, DO NOT allow the high-
pressure spray to come in contact with unprotected skin, eyes,
or with any pets or animals. Serious injury will occur.

CAUTION: Before operation:
ʵ Connect the water supply to the pressure washer. For
instructions on connecting the water supply to the pressure
on the top of the high pressure foam
20
13 rotates for vertical or
4 securely with other hand.