Hatco IWRM Série Manuel D'installation Et D'utilisation page 13

Réchaud à induction
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Flush Mount Kit
The flush mount kit allows flush-style installation of the unit into
a standard, non-stepped countertop cutout. This installation
requires the purchase of the Flush Mount Kit accessory and can
be performed in a solid material or stainless steel countertop.
IWRMB-FLUSH-MNT = Model IWRM-B1-1313-06
Use the following procedure for flush mount kit installation.
1. Carefully measure and cut the opening in the countertop.
13-1/8"
(333 mm)
Flush Mount Kit Installation Countertop Cutout
2. Cut and drill the appropriate holes in the vertical surface
where the control enclosure will be installed. Refer
to the "Installing the Control Panel" procedure in the
INSTALLATION section for details.
3. Cut the required openings in the cabinetry to provide proper
ventilation to the induction range. Refer to the "Ventilation
Requirements" in the INSTALLATION section for details.
4. If necessary, make structural modifications or add bracing
underneath the countertop to ensure the countertop will
support the weight of the unit and its contents.
NOTE: The countertop must be level to ensure proper operation
of the Induction Warmer.
5. Install the two included
mounting brackets to
the underside of the
countertop along two
sides of the cutout, one
across from the other.
• Position the brackets
so
that
there
12-1/32" (306 mm) of
clear space between
the brackets; so the
base of the warmer
will fit between the brackets.
• Secure the brackets to the countertop using three of the
included mounting screws for each bracket.
6. Install the included warmer support strips onto the bottom
of the Induction Warmer flange. These strips will help
support the warmer and prevent the silicone sealant from
leaking past the glass. To install a caulk support strip:
a. Remove the paper from the adhesive on the strip.
b. Position the strip so that it extends about 1/32" (1 mm)
beyond the glass surface on each side.
Form No. IWRMM-0119
13-1/8"
(333 mm)
Underside of countertop.
12-1/32"
(306 mm)
is
Installed
mounting brackets.
OPTIONS AND ACCESSORIES
Underside of
countertop.
Mounting Bracket
Leveling Screw
Installing the Mounting Brackets
7. Install the included leveling screws with lock nuts into the
mounting brackets.
8. Adjust the leveling screws so they are approximately 1/2"
(13 mm) from the top side of the countertop.
9. Carefully lower the unit into the cutout and set it on top of
the leveling screws. Make sure the power cord and control
cable do not get pinched.
10. Adjust each leveling screw until the glass surface of the
Induction Warmer is level with the countertop.
Silicone
Back
of
Unit
Power Cord
Leveling Screw
Flush Mount Kit Installation
11. Tighten the lock nuts against the bottom of the mounting
brackets to prevent the leveling screws from loosening.
12. Apply a bead of National Sanitation Foundation (NSF)-
approved silicone sealant in the gap between the
countertop and the Induction Warmer. To apply a clean,
consistent sealant bead:
a. Make sure the unit is centered in the countertop cutout.
b. Install masking tape on each side of the gap to define the
edge of the sealant.
c. Carefully apply sealant into the gap.
d. Quickly smooth the sealant surface.
e. Carefully remove the masking tape before the sealant
dries.
NOTE: The silicone sealant must be rated for use at
temperatures up to 250°F (121°C)
13. Install the control panel in the desired location. Refer
to the "Installing the Control Panel" procedure in the
INSTALLATION section for details.
14. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
13
Mounting
Screw
Lock Nut
Glass surface level
with countertop.
Front
of
Unit
Countertop
Control Cable Port

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

Iwrm-c1-1317-06Iwrm-cd1-03Iwrm-b1-1313-06

Table des Matières