Publicité
Les langues disponibles
Les langues disponibles
ADDITIONAL SPECIFIC SAFETY RULES
1.
DO NOT OPERATE THIS MACHINE until it is
completely assembled and installed according to the
instructions. A machine incorrectly assembled can
cause serious injury.
2.
OBTAIN ADVICE from your supervisor, instructor,
or another qualified person if you are not thoroughly
familiar with the operation of this machine. Knowledge
is safety.
3.
FOLLOW ALL WIRING CODES and recommended
electrical
connections
electrocution.
4.
DO NOT OPERATE ON ANYTHING OTHER THAN
THE DESIGNATED VOLTAGE for the saw.
5.
SECURE THE MACHINE TO A STABLE SUPPORTING
SURFACE. Vibration can possibly cause the machine
to slide, walk, or tip over, causing serious injury.
6.
USE ONLY CROSSCUT SAW BLADES. Use only
zero-degree or negative hook angles when using
carbide-tipped blades. Do not use blades with deep
gullets. These can deflect and contact the guard, and
can cause damage to the machine and/or serious
injury.
7.
USE ONLY BLADES OF THE CORRECT SIZE AND
TYPE specified for this tool to prevent damage to the
machine and/or serious injury.
8.
MAKE CERTAIN BLADE ROTATES IN CORRECT
DIRECTION and that the teeth at the bottom of the
blade point to the rear of the saw.
9.
USE BLADE GUARD AT ALL TIMES. Don't spray any
lubricants or cleaners (particularly spray or aerosol) in
the vicinity of the plastic guard. The polycarbonate
material sued in the guard is subject to attack by
certain chemicals.
10.
USE A SHARP BLADE. Check the blade to see if it
runs true and is free from vibration. A dull blade or
a vibrating blade can cause damage to the machine
and/or serious injury.
11.
DON'T WEDGE ANYTHING AGAINST THE FAN to
hold the motor shaft.
12.
DON'T USE ABRASIVE WHEELS. The excessive
heat and abrasive particles generated by them will
damage the saw.
13.
INSPECT BLADE FOR CRACKS or other damage
prior to operation. A cracked or damaged blade can
come apart and pieces can be thrown at high speeds,
causing serious injury. Replace cracked or damaged
blades immediately.
14.
CLEAN THE BLADE AND BLADE FLANGES prior to
operation. Cleaning the blade and flanges allows you
to check for any damage to the blade or flanges. A
cracked or damaged blade or flange can come apart
and pieces can be thrown at high speeds, causing
serious injury.
15.
ALWAYS USE THE KERF PLATE AND REPLACE
THIS PLATE WHEN DAMAGED. Small chip
accumulation under the saw may interfere with the
saw blade or may cuase instability of workpiece when
cutting.
16.
USE ONLY BLADE FLANGES specified for this tool
to prevent damage to the machine and/or serious
injury.
17.
CLEAR THE AREA OF FLAMMABLE LIQUIDS and/
or gas prior to operation. Sparks can occur that would
ignite the liquids and cause a fire or an explosion.
18.
CLEAN THE MOTOR AIR SLOTS of chips and
sawdust. Clogged motor air slots can cause the
machine to overheat, damaging the machine and
possibly causing a short which could cause serious
injury.
19.
TIGHTEN THE TABLE CLAMP HANDLE and any
SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others.
Failure to follow these rules may result in serious personal injury.
to
prevent
shock
or
other clamps prior to operation. Loose clamps can
cause parts or the workpiece to be thrown at high
speeds.
20.
NEVER START THE TOOL with the blade against the
workpiece. The workpiece can be thrown, causing
serious injury.
21.
KEEP ARMS, HANDS, AND FINGERS away from the
blade to prevent severe cuts. Clamp all workpieces
that would cause your hand to be in the "Table
Hazard Zone" (within the red lines).
22.
DON'T PLACE HANDS IN THE BLADE AREA when
the saw is connected to a power source.
23.
DON'T REACH UNDERNEATH THE SAW unless it
is unplugged or turned off. The saw blade is exposed
on the underside of the saw.
24.
ALLOW THE MOTOR TO COME TO FULL SPEED
prior to starting cut. Starting the cut too soon can
cause damage to the machine or blade and/or
serious injury.
25.
NEVER REACH AROUND or behind the saw blade.
A moving blade can cause serious injury.
26.
NEVER CUT FERROUS METALS or masonry. Either
of these can cause the carbide tips to fly off the blade
at high speeds causing serious injury.
27.
NEVER CUT SMALL PIECES. Cutting small pieces
can cause your hand to move into the blade, resulting
in serious injury.
28.
NEVER LOCK THE SWITCH in the "ON" position.
Setting up the next cut could cause your hand to
move into the blade, resulting in severe injury.
29.
NEVER APPLY LUBRICANT to a running blade.
Applying lubricant could cause your hand to move
into the blade, resulting in serious injury.
30.
DO NOT PERFORM FREE-HAND OPERATIONS.
Hold the work firmly against the fence and table.
Free-hand operations on a miter saw could cause
the workpiece to be thrown at high speeds, causing
serious injury. Use clamps to hold the work when
possible.
31.
TURN OFF THE MACHINE and allow the blade to
come to a complete stop prior to cleaning the blade
area or removing debris in the path of the blade. A
moving blade can cause serious injury.
32.
PROPERLY SUPPORT LONG OR WIDE WORK-
PIECES. Loss of control of the workpiece can cause
injury.
33.
NEVER PERFORM LAYOUT, ASSEMBLY, OR SET-UP
WORK on the table/work area when the machine is
running. A sudden slip could cause a hand to move
into the blade. Severe injury can result.
34.
DON'T ALLOW ANYONE to stand behind the saw.
35.
TURN THE MACHINE "OFF", disconnect the machine
from the power source, and clean the table/work area
before leaving the machine. LOCK THE SWITCH IN
THE "OFF" POSITION to prevent unauthorized use.
Someone else might accidentally start the machine
and cause injury to themselves.
36.
BEFORE OPERATING THE SAW, check and securely
lock the bevel, miter, and sliding fence adjustments.
37.
ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video) is available from the Power Tool Institute, 1300
Sumner Avenue, Cleveland, OH 44115-2851 (www.
powertoolinstitute.com). Information is also available
from the National Safety Council, 1121 Spring Lake
Drive, Itasca, IL 60143-3201. Please refer to the
American National Standards Institute ANSI 01.1
Safety Requirements for Woodworking Machines and
the U.S. Department of Labor regulations.
5
Publicité
