Error Codes - Migatronic MWF 552 YARD Manuel D'instruction

One of the below mentioned error codes will be displayed if an error occurs during software update.
Error codes for MWF software 10001801.cry
Error code Cause and solution
There is no software present in the
control unit.

Insert a SD card with software in
the control unit and turn on the
machine.
SD card is not formatted.

The SD card must be formatted in
a PC as FAT and place the files
down on the card or use another
SD card.
SD card contains no software.

See the previous page.
SD card has more files of the same
name.

See the previous page.
The control unit has tried to read
more data than is accessible in the
memory.
1. Insert the SD card again.
2. Replace the SD card.
3. Contact MIGATRONIC Service.
Software on the SD card is locked
for another type of control unit.

Use a SD card with software that
matches your control unit.
Software on the SD card is locked
for another control unit with another
serial number/ bar code.

Use a SD card with software that
matches your control unit.
The internal copy protection does
not allow access to the
microprocessor.
1. Insert the SD card in the machine
again.
2. Contact MIGATRONIC Service.
The memory circuit is defective in
the control unit.

Contact MIGATRONIC Service.
The memory circuit is defective in
the control unit.

Contact MIGATRONIC Service
The file 10001801.cry has an error.
1. Insert the SD card in the machine
again.
2. Exchange the SD card.
Lacking communication to the
power source
1. The power source is a MK1
version and cannot communicated
with wire feed unit MK2 version.
2. The intermediary cable is
damaged.
3. Insert the SD card in the machine
again.
4. Contact MIGATRONIC Service.

ERROR CODES

Error codes for welding program package 106454xx.bin
Error code
Error codes for Power control package 10001702.cry
Error code
10
Cause and solution
There is no welding programs present in the
control unit

Insert a SD card with software in the control unit
and turn on the machine. See the previous
page.
SD card is not formatted.

The SD card must be formatted in a PC as FAT
or use another SD card.
It is only possible to have one file with welding
programs.

Make sure that there is only one file with the
number 106454xx.bin on the SD card. See the
previous page.
The welding program package does not match
this control unit.

Use a SD card with software that matches your
control unit.
The welding program package is locked for
another control unit with another serial number/
bar code.

Your software package is copy protected and
cannot be used for a control unit without the
correct license.
The control unit is defective

Contact MIGATRONIC Service.
The file 106454xx.bin is not present on the SD
card.

See the previous page.
The file 106454xx.bin has an error.
1. Insert the SD card in the machine again.
2. Exchange the SD card.
The Sigma folder with files are not present at the
card or are saved incorrectly.
1. Make a folder MIGA_SW / SIGMA as described
on the previous page and save the files in the
folder.
2. Exchange the SD card
The internal memory is to small

Welding program package cannot be loaded
Cause and solution
The file 10001702.cry has an error.
1. Insert the SD card in the machine again.
2. Exchange the SD card.
SD card is not formatted.

The SD card must be formatted in a PC as FAT.
Or use another SD card.
The software does not match this control unit.

Use a SD card with software that matches your
control unit.
DSP-PCB is defective

Contact MIGATRONIC Service
Data transmission error

Turn on and off the machine. Exchange the SD
card if the error is displayed again. Contact your
dealer if necessary.
The file 10001702.cry has an error.
1. Insert the SD card in the machine again.
2. Exchange the SD card.
DSP-PCB is defective

Contact MIGATRONIC Service