Milwaukee 2541-20 Manuel De L'utilisateur page 5

OPERATION
To reduce the risk of injury, always
WARNING
wear safety goggles or glasses
with side shields. The operator and other people
in the work area must wear eye protection in ac-
cordance with ANSI Z87.1. Eye protection does
not fit all operators in the same way. Make sure
the eye protection chosen has side shields or
provides protection from flying debris both from
the front and sides. The employer is responsible
for enforcing the use of eye protection by the
operator and other people in the work area. When
required, wear head protection in accordance
with ANSI Z89.1.
To reduce the risk of injury to yourself and others,
test the tool before beginning work each day ac-
cording to the "Required Daily Testing" section.
Do not use the tool unless you thoroughly under-
stand the actuation mode selected.
Remove battery pack and fasteners before leav-
ing the work area, moving the tool to another
location, or handing the tool to another person.
Failure to do so could result in serious injury.
Do not use this tool for fastening electrical
cables. It is not designed for electric cable
installation and may damage the insulation of
electric cables thereby causing electric shock
or fire hazards.
NEVER wedge or hold back the workpiece con-
tact mechanism during operation of the tool.
Never attempt to clear a jammed workpiece con-
tact by grasping the discharge area of the tool.
Doing so could result in serious injury.
To avoid serious injury, do not attempt to prevent
the recoil by holding the tool too firmly against
the work. Keep face and body away from the
tool. During normal use, the tool will recoil im-
mediately after driving a fastener. This is a normal
function of the tool. Restriction to the recoil can
result in a second fastener being driven when
the tool is in Contact Actuation mode. Grip the
handle firmly, let the tool do the work, and do not
place a second hand on top of the tool.
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool on. The fuel gauge will light up for 2-3
seconds. When less than 10% of charge is left, 1
light on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel gauge
will flash 8 times and the tool will not run. Charge
the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash and the tool will not run. Allow the battery
to cool down.
Power/Actuation Selection
1. Install battery pack.
2. Press and hold the power button
tool (the power button's green LED ring will light).
The battery LED indicates when the battery level
is sufficient to operate the tool.
Power
button
Actuation
indicator
LED
3. Press and hold the MODE button to toggle
between single sequential actuation mode and
contact (bump) actuation mode.
WARNING! Understand actuation process before
use.
Single Sequential Actuation -
The workpiece contact and then the
trigger must be activated in a specific
sequence to drive a fastener.
Contact (Bump) Actuation -
The workpiece contact and the trigger
can be activated in any sequence to
drive a fastener.
4. Press and hold the power button
tool.
Single Sequential Actuation
1. Grip the handle firmly.
2. Push the tool against the work surface, compress-
ing the workpiece contact.
3. Pull the trigger to drive the fastener.
WARNING! To avoid serious injury, do not at-
tempt to prevent the recoil by holding the tool too
firmly against the work.
4. Remove your finger from the trigger and remove
the tool from the workpiece.
Contact (Bump) Actuation
Contact actuation can follow two different sequences,
depending on your use.
Multiple actuations:
1. Grip the handle firmly.
2. Pull and hold the trigger.
3. Push the tool against the work surface, compress-
ing the workpiece contact to drive the fastener.
WARNING! To avoid serious injury, do not attempt
to prevent the recoil by holding the tool too firmly
against the work.
4. Continue to hold the trigger and repeat workpiece
contact.
Single actuation:
1. Grip the handle firmly.
2. Push the tool against the work surface, compress-
ing the workpiece contact.
3. Pull the trigger to drive the fastener.
WARNING! To avoid serious injury, do not attempt
to prevent the recoil by holding the tool too firmly
against the work.
4. Remove your finger from the trigger and remove
the tool from the workpiece.
5
to turn on the
to turn off the
Operation
Battery
LED
Actuation
indicator
LED