Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Frame rail
Hitch Shown In Proper Position
Fastener Kit: 24896F
Equipment Required: Tin Snips
Wrenches: 13mm, 11/16
Drill: 1/2 drill bit
Remove exhaust hanger – Drivers side
Figure 2
Trim heat shield in area shown – Drivers side
Figure 3
Qty. (2)
Hex bolt 1/2-13 X 1.50 GR5
Qty. (2)
1/2 Conical washer
Qty. (2)
Handle Nut
Qty. (4)
Bolt, M8-1.25 x 40mm CL10.9
1.
Lower exhaust system by removing drivers side (2) M8 bolts holding exhaust hanger and return bolts to vehicle owner. Remove the middle
exhaust hanger and save bolts.– See figure 2.
2.
Trim heat shield in area where hitch side bracket mounts to the bottom of the frame – See figure 3.
3.
Cut plastic isolator strips in half and apply the two halves of each strip to bottom of hitch driver side bracket between slot and large access
hole – See figure 4. Note: The isolators strips go between the exhaust hanger and side bracket.
4.
Raise hitch into position and re-install driver's side exhaust hangers using the M8-1.25 x 40mm bolts, lock washers, and flat washers on both
sides provided with hitch. Re-install middle exhaust hanger with original hardware.
5.
With hitch in place use hitch as template to drill 1/2" hole in frame. Use handle nut provided to install 1/2" bolts and conical washers.
6.
Torque all fasteners to specifications.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2012 Cequent Performance Products, Inc
Installation Instructions
Ford C-Max
Fascia
Drawbar Kit:
Drawbar must be used in the
Rise position only.
7
Apply plastic isolator strips
To bottom of hitch side bracket
Diver side.
Figure 4
Tighten all 1/2-13 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all M8-1.25 CL10.9 fasteners with torque wrench to 27 Lb.-Ft. (37 N*M)
3593
Wiring Access Location: PC1, 2
Frame rail
4 5 6
Figure 1
Qty. (4)
5/16 Flat Washer
Qty. (4)
5/16 Lock Washer
Qty. (2)
Plastic Isolators
Sheet 1 of 3
24896N
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Accessory Rating
Access hole
Fasteners typical
both sides
1 2 3
10-4-12
Form F206 Rev A 5605
24896
60318
77284
A
Rev. B
Publicité
Manuels Connexes pour Cequent Performance Products 24896
Sommaire des Matières pour Cequent Performance Products 24896
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2012 Cequent Performance Products, Inc Sheet 1 of 3 24896N 10-4-12 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2012 Cequent Performance Products, Inc. Feuille 1 de 3...
- Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2012 Cequent Performance Products, Inc. Hoja 1 de 3 24896N 10-4-12 Rev.