Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required: 7/16" Pull Wire
Fastener Kit: 24894F
Wrenches: 11/16", 7/8"
Drill Bits: 1/2"
0.563 (14.30 mm)
Note: Drill rearward
of existing 3/4"
diameter hole
in frame rail
Figure 1: Access hole modification to allow
pull wiring of block and carriage bolt
B. Align block on
A. Insert bolt and
access hole
Block into frame
Figure 2: Pull Wire Procedure
1 1 1 1
Qty. (2)
7/16"-14 x 1.50" Carriage Bolt GR.5
2 2 2 2
Qty. (2)
3" x 7/8" Block
3 3 3 3
Qty. (2)
7/16" Conical Washer
4 4 4 4
Qty. (2)
7/16"-14 Hex Nut GR. 2
1.
Lower the exhaust by removing the rubber exhaust isolator located above the muffler.
2.
Use 1/2" drill to enlarge the existing 3/4" holes on both frame rails as shown in Figure 1.
3.
Install 7/16" carriage bolts and 7/8" blocks using the reverse pull wire procedure shown in Figure 2. Leave pull wires attached.
4.
Raise hitch into position and feed pull wires through the holes on the hitch brackets.
5.
Install the 1/2" carriage bolt and 2" x 2" spacer to tie down hook as shown in Figures 3 & 4. Do not tighten down at this point.
6.
Feed the 7/16" carriage bolts though the holes on the hitch brackets, remove pull wires, and install fasteners as shown in Figure 3.
7.
Center the hitch on the vehicle and torque all fasteners to the specifications shown below.
8.
Reinstall exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2012, 2015 Cequent Performance Products, Inc. – Printed in Mexico
Installation Instructions
Fascia
Chevy Spark 2LT
(Sold separately)
Drawbar Kit:
3594
Drawbar must be used in the
RISE position only.
1 1 1 1
2 2 2 2
3 3 3 3
4 4 4 4
Tie down hook
C. Pull bolt thru
block
Pull Wire
Tighten all 7/16" fasteners with torque wrench to 50 Lb.-Ft (68 N-M).
Tighten all 1/2"-13 fasteners with torque wrench to 75 Lb.-Ft (102 N-M).
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
Note: Orientation of Block
5 5 5 5
6 6 6 6
7 7 7 7
8 8 8 8
Figure 3: Hitch Installation
5 5 5 5
Qty. (1)
1/2"-13 x 1.75" Carriage Bolt GR.5
6 6 6 6
Qty. (1)
2" x 2" Spacer
7 7 7 7
Qty. (1)
1/2" Conical Washer
8 8 8 8
Qty. (1)
1/2"-13 Hex Nut GR. 2
Sheet 1 of 3
24894N
Part Numbers:
24894
60313
77282
Manufacturer's Rating or
Tie down hook
Figure 4: Back view of
properly Fastened
To Tie Down Hook
1 1 1 1
2 2 2 2
3 3 3 3
4 4 4 4
10-6-15
Hitch
Rev. B
Publicité
Manuels Connexes pour Cequent Performance Products 24894
Sommaire des Matières pour Cequent Performance Products 24894
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24894N 10-6-15 Rev. B z 2012, 2015 Cequent Performance Products, Inc. – Printed in Mexico...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. z 2012, 2015 Cequent Performance Products, Inc. - Imprimé au Mexique Fiche 2 de 3...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 10-6-15 Rev. B z 2012, 2015 Cequent Performance Products, Inc. - Impreso en México Hoja 3 de 3 24894N...