Publicité
Les langues disponibles
Les langues disponibles
Place the gas bottle in the gas bottle holder
Never place the gas bottle on the other side of the base
plate
.
[
22 ]
Do not keep a second gas bottle in the cabinet .
Before connecting the gas bottle to the product, remove any
dirt from the heads of the gas bottle, the regulator or the
burner . Dirt, spiders and insects could be inside and block
the burner or Venturi tube at the opening . A blocked burner
can cause a fire under the product .
Clean blocked burner openings with a pipe cleaner .
Do not use an additional seal .
Do not block the ventilation openings when using the gas
bottle . The ventilation openings of the gas bottle must stay
open at all times .
Before each use, check all connections for gas leaks .
Perform the test with soapy water .
Never use a naked flame to find leaks .
Replace the gas bottle away from any source of ignition .
1 .
Place the gas bottle in the gas bottle holder
plate
.
22 ]
[
2 .
Connect the low pressure regulator
tightening it on with your hands .
3 .
Follow the instructions enclosed with the regulator .
˜ Checking for gas leaks
1 .
Mix 1 part of washing-up liquid to 3 parts of water (approx .
50 ml) .
Rotate all knobs to the OFF position .
2 .
3 .
Connect the low pressure regulator
(see "Connecting the gas bottle") .
4 .
Switch on the burner with the knob .
5 .
Switch on the gas supply by opening the gas bottle's fitting .
6 .
Apply the soapy water to the gas hose
connections . If bubbles appear, this indicates a leak .
Replace the defective part immediately .
˜ Piezo ignition
Z4
Knob
Burner
1+2
Main burners
3+4
High-power burners
5
Side burner
8
GB/IE/NI
(Fig . I) .
32 ]
[
in the base
[
32 ]
to the gas bottle by
34 ]
[
to the gas bottle
34 ]
[
and all
34 ]
[
[
40 ]
Icon
Meaning
Big flame
Small flame
Rotate all knobs to the OFF position .
1 .
2 .
Open the valve on the gas bottle .
Press and hold the knob (1) . Rotate the knob to the left up to
3 .
the
position . The ignition occurs automatically . A clicking
sound indicates that the product is igniting . If the flame does
not burn upon the first try, repeat the process 4 to 5 times
until the flame is burning .
Optional: Proceed as described above to ignite the other
4 .
burners with knobs (2), (3), (4) and (5) .
5 .
Set the desired temperature according to the scales on
the knobs .
INFO: Allow the product to pre-heat for approx . 15 minutes
before adding food to achieve better cooking results .
˜ Burn-in technique
m
DANGER! Risk of fire! Risk of injuries! Risk of
burns!
Do not spray the oil directly onto the main burners, the high-
power burners and the side burner
Do not leave the product unattended at all times during the
burn-in process . Switch off all burners and let the product
cool down before leaving the product .
INFO:
Carry out the burn-in technique to clean the internal parts
o
and to burn off any residues caused by manufacturing .
Use heat-resistant oil (e .g . canola oil or sunflower oil) .
o
1 .
Remove the following parts from the product (Fig . Z3):
Warming rack
–
2 ]
[
Flame diffusers
–
3 ]
[
High-power burner flame diffusers
–
Grate
–
[
9 ]
Grill grate
–
[
10 ]
Grate with grill-in-grill system
–
Grate
–
39 ]
[
2 .
Spray the inside of the product with oil . It is important to
spray the internal area of the burner housing with lid
(Fig . Z3) .
3 .
Wipe the inside of the product with a cloth or towel on all
the places where the oil has been sprayed . Thoroughly
wiping the oil into the product is important to make sure the
oil is spread around the whole area .
4 .
Spray the following parts with oil:
Warming rack
–
[
2 ]
Flame diffusers
–
3 ]
[
High-power burner flame diffusers
–
Grate
–
[
9 ]
Grill grate
–
10 ]
[
Grate with grill-in-grill system
–
.
40 ]
[
4 ]
[
11 ]
[
1 ]
[
4 ]
[
11 ]
[
Publicité
