Publicité
Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety instructions for edge routers
Hold the power tool by insulated gripping surfaces
u
only, because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the work by your hand or against the body leaves it un-
stable and may lead to loss of control.
The permitted speed of the cutting bit must be at least
u
equal to the maximum speed marked on the power
tool. If cutting bits run faster than their rated speed, they
may break and fly off.
Routers and other accessories must be able to fit ex-
u
actly in the tool holder (collet) of your power tool. Ap-
plication tools that do not fit exactly in the tool holder of
the power tool will turn unevenly, vibrate heavily and may
cause a loss of control.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Never rout over metal objects, nails or screws. The
u
router could become damaged and cause increased vibra-
tion.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Do not use blunt or damaged routers. Blunt or damaged
u
routers cause increased friction, create imbalances and
may become jammed.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Products sold in GB only:
Bosch Power Tools
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for copy routing as well as routing
grooves, edges, profiles and elongated holes in wood,
plastic and light building materials while resting firmly on the
workpiece.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Drive unit
(2) Routing base
(3) Carbon brush bracket
(4) Nut for routing guide
(5) Chip deflector
(6) Knurled screw for routing base
(7) Router bit
a)
(8) Cap nut with collet
(9) Guide plate
(10) Base plate
(11) Dust extraction adapter
(12) Wing bolt for routing base
(13) On/off switch
(14) Handle (insulated gripping surface)
(15) Scale for setting routing depth
(16) Collet
(17) Tool holder
(18) Open-ended spanner (10 mm)
(19) Open-ended spanner (17 mm)
(20) Guide bushing
a)
(21) Parallel guide
a)
(22) Wing bolt for parallel guide
English | 13
a)
a)
a)
1 609 92A 8RH | (10.08.2023)
Publicité
