Publicité
Les langues disponibles
Les langues disponibles
B
OUTSIDE BACK EXHAUST
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
PREPARING THE REAR WALL
B1.
FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for
outside exhaust.
NOT E:
READ
IT IS VERY
AND FOLL
IMPO RTAN
IN THE
OW THE
T TO
BEFO
INST ALLA
DIRE CTIO
RE PRO
TION INST
NS
REAR
CEED
RUC TION
WAL L
TEM PLAT
ING WITH
S
This Rear
Wall Templa
E.
THIS
3/8" TO EDGE
mounti
ng plate
te serves
outlet.
and to
to positio
12"
1. Use
locate the
horizon
n the bottom
a level
to check
tal exhaus
accura
tely.
that the
t
2. Locate
and mark
templa
te is positio
right side
at least
ned
of the centerl
one stud
on the
4"
screw mounte
I t is importa
ine.
left or
d firmly
nt to use
at least
of the microw
in a stud
one wood
locatio ns
for the
ave. Mark
two additio
to suppor
3. Drill
holes in
supplie
nal, evenly
t the weight
a stud,
the marked
d toggle
bolts.
spaced
that do
drill a 3/16"
locatio ns.
not line
hole for
wood screws
Where
there is
toggle
bolts.
up with
a stud,
. For holes
drill 5/8"
AT THIS
D O NOT
INSTA LL
holes for
4. Remov
TIME.
THE MOUN
5. Review
e the templa
TING PLATE
the Installa
te from
installa
tion situatio
tion Instruc
the rear
wall.
n.
tion book
for your
Darle vuelta
versió n
a la hoja
en Españ
para consu
ol.
ltar la
Loca te
and mark
moun ting
holes to
plate .
align with
IMPO RTAN
holes in
T:
the
LOCA
TE AT
LEAS T
THE CEN
ONE STUD
MAR K
TERL INE.
ON EITH
THE LOCA
ER SIDE
SPAC
TION FOR
OF
ED TOG
AREA
GLE BOLT
2 ADD
ITION AL,
.
S IN THE
EVEN
MOU NTIN
LY
G PLAT
E
Trim the
rear wall
temp late
along
the dotte
d line.
Loca te
and mark
moun ting
plate .
IMPO RTAN
LOCA
T:
TE AT
THE CEN
LEAS T
TERL INE.
MAR K
THE LOCA
SPAC
ED TOG
AREA
GLE BOLT
.
•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
Installation Instructions
NOTE: IT IS VERY IMPORTANT
READ AND FOLLOW
IN THE INSTALLATION
BEFORE PROCEEDING
REAR WALL TEMPLATE.
This Rear Wall Template
serves to position the bottom
the horizontal exhaust
mounting plate and to locate
outlet.
1. Use a level to check
that the template is positioned
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
I t is important to use at
a stud to support the weight
screw mounted firmly in
of the microwave. Mark
two additional, evenly spaced
toggle bolts.
locations for the supplied
locations. Where there is
3. Drill holes in the marked
a stud, drill a 3/16" hole
for wood screws. For holes
that do not line up with a
stud, drill 5/8" holes for
toggle bolts.
D O NOT INSTALL THE
AT THIS TIME.
4. Remove the template
from the rear wall.
Instruction book for your
5. Review the Installation
installation situation.
Darle vuelta a la hoja
para consultar la
versión en Español.
Locate and mark holes
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
THE CENTERLINE.
MARK THE LOCATION
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
Trim the
rear wall
temp late
along
the dotte
d line.
holes to
align with
holes in
the
ONE STUD
ON EITH
ER SIDE
TION FOR
OF
2 ADD
S IN THE
ITION AL,
EVEN
MOU NTIN
LY
G PLAT
E
(Horizontal Duct)
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
TO
THE DIRECTIONS
INSTRUCTION S
WITH THIS
4"
least one wood
MOUNTING PLATE
to align with holes in the
STUD ON EITHER SIDE
OF
EVENLY
FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
STUD ON EITHER SIDE
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
REMOVE BLOWER PLATE
B2.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Blower Plate
EN-16
Back of
Microwave
Publicité
