DeWalt DCD701 Guide D'utilisation page 6

English
• crystalline silica from bricks and cement and other masonry
products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing dust
to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse
dust, which may cause serious and permanent respiratory or
other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles
away from face and body.

WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19) during
use. Under some conditions and duration of use, noise from
this product may contribute to hearing loss.

CAUTION: When not in use, place tool on its side
on a stable surface where it will not cause a tripping
or falling hazard. Some tools with large battery packs
will stand upright on the battery pack but may be easily
knocked over.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught in
moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
OPM .................... oscillations per
minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.
6
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... avoid staring at
light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
IPXX .................... IP symbol
Belt Hook and Bit Clip (Fig. B)
Optional Accessory

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the tool
from a work belt. DO NOT use the belt hook for tethering
or securing the tool to a person or object during use. DO NOT
suspend tool overhead or suspend objects from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.
iMPORTAnT: When attaching or replacing the belt hook or
bit clip, use only the screw
securely tighten the screw.
The belt hook 11 and bit clip
either side of the tool using only the screw
accommodate left- or right-handed users. If the belt hook
or bit clip is not desired at all, they can be removed from
the tool.
To move the belt hook or bit clip, remove the screw that
holds it in place then reassemble on the opposite side. Be
sure to securely tighten the screw.
Installing a Bit or Accessory into a Keyless Chuck
(Fig. C)

WARNING: Do not attempt to tighten drill bits (or any
other accessory) by gripping the front part of the chuck and
turning the tool on. Damage to the chuck and personal injury
may result. Always lock off trigger switch and disconnect tool
from power source when changing acces sories.

WARNING: Always ensure the bit is secure before starting
the tool. A loose bit may eject from tool causing possible
personal injury.
To insert a drill bit or other accessory, follow these steps.
1. Turn tool off and remove battery pack.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 3/4" (19 mm) into the
chuck and tighten securely by rotating the chuck
9
sleeve clockwise with one hand while holding the tool
8
with the other. Your tool is equipped with an automatic
spindle lock mechanism. This allows you to open and close
the chuck with one hand.
Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
Speed Selection (Fig. A)
The tool features two speed settings for greater versatility.
nOTE: Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changing speed.
1. To select speed 1 (higher torque setting), slide the speed
selector back (away from the chuck).
6
2. To select speed 2 (lower torque setting), slide the speed
selector forward (towards the chuck).
If the tool does not change speeds, confirm that the speed
selection switch is completely engaged in the forward or
back position.
that is provided. Be sure to
12
13 can be attached to
12 provided, to