Bosch GWS 30-180 PB Professional Notice Originale page 23

wires by applying excessive load to the brush The wire
bristles can easily penetrate light clothing and/or skin.
If the use of a guard is specified for wire brushing, do
u
not allow any interference of the wire wheel or brush
with the guard. Wire wheel or brush may expand in dia-
meter due to work load and centrifugal forces.
Additional safety information
Wear safety goggles.
The protective guard must not be used for
cutting. With a suitable adapter, the protective
guard can also be used for cutting.
Hold the power tool firmly with both hands
and make sure you have a stable footing. The
power tool can be more securely guided with
both hands.
For application tools with an internal thread, such as
u
brushes and diamond annular cutters, attention must
be paid to the max. thread length of the grinding
spindle. The spindle end must not touch the base of the
application tool.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the off position
u
when the power supply is interrupted, e. g., in case of
a power failure or when the mains plug is pulled. This
prevents uncontrolled restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Store the application tools inside buildings, in a dry,
u
frost-free room at a uniform temperature.
Remove the application tools before transporting the
u
power tool. This will allow you to avoid damage.
Bonded cutting and grinding discs have an expiration
u
date, after which the discs must no longer be used.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
Bosch Power Tools
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting and brushing metal,
stone and plastics, as well as roughing metal and making
holes in stone materials using diamond annular cutters,
without the use of water. Make sure that the correct protect-
ive guard is used (see "Operation", page 27).
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
The power tool must not be used to grind stone materials
with diamond grinding heads, or to work on composite ma-
terials.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Spindle lock button
(2) Status indicator (LED)
(3) On/off switch
(4) Dust filter
(5) Standard auxiliary handle (insulated gripping sur-
face)
(6) Vibration-damping auxiliary handle (insulated grip-
ping surface)
(7) Two-pin spanner for clamping nut
(8) Protective guard for grinding with clamping lever
(9) Protective guard for grinding with locking screw
(10) Coding cam
(11) Clamping lever for protective guard
(12) Locking screw for protective guard
(13) Adjusting screw for protective guard
a)
(14) Grinding disc
(15) Clamping nut
(16) Quick-clamping nut
(17) Protective guard for cutting with clamping lever
(18) Protective guard for cutting with locking screw
(19) Cover for cutting
English | 23
a)
a)
a)
a)
a)
1 609 92A 9AU | (09.04.2024)