Bosch PowerMore 250 Notice D'utilisation D'origine page 15

The eBike battery can be charged at any state of charge. In-
terrupting the charging process does not damage the eBike
battery.
The eBike battery has a temperature monitoring function
that only allows it to be charged within a temperature range
of 0 °C to 40 °C.
Do not reconnect the eBike battery to the charger until it has
reached the correct charging temperature.
Battery charge indicator outside of the eBike
Note: The PowerMore battery charge indicator (2) switches
back off as soon as the eBike battery is switched on.
The five LEDs on the battery charge indicator (2) show the
battery's state of charge when the eBike battery is switched
on.
Each LED represents approximately 20 % of the charging ca-
pacity. When the eBike battery is fully charged, all five LEDs
will be lit.
The eBike battery's state of charge when switched on is also
shown on the display of the on-board computer. Read and
follow the instructions in the operating manuals for the drive
unit and on-board computer.
If the eBike battery's capacity is less than 10 %, the last re-
maining LED will flash.
Once charging is complete, disconnect the eBike battery
from the charger and the charger from the mains.
Laying the Cable on the PowerMore Battery
Holder (see figure A)
Note: When laying the cable (6), make sure that the
cable (6) is fed under the release button (10). This prevents
the release button (10) from being pressed accidentally and
causing the PowerMore battery to be released.
Inserting and Removing the PowerMore Battery
When inserting the battery into the holder or remov-
u
ing it from the holder, always switch off the eBike bat-
tery and the eBike beforehand.
Once you have inserted the eBike battery, check that
u
it is correctly positioned and secure in all directions.
Only leave the PowerMore battery with the cable con-
u
nected to the eBike.
Once the PowerMore battery is installed, the connec-
u
tion socket of the battery must not face upwards.
Inserting the PowerMore Battery (see figure B)
To insert the battery (1), place its guide grooves (12) onto
the guide rails (11). Ensure that the battery is aligned cor-
Bosch eBike Systems
If the temperature of the
eBike battery is outside this
charging range, three of the
LEDs on the battery charge
indicator (2) will flash. Dis-
connect the eBike battery
from the charger and let it
reach the correct temperat-
ure range.
rectly and that the battery is positioned in both guide rails.
Slide the battery (1) into the holder (9) until it audibly clicks
into place.
Insert the cable connector (4) into the connection
socket (3). Ensure that the cable connector (4) is aligned
correctly.
Insert the cable connector (7) into the eBike charging
socket (8). Ensure that the cable connector (7) is aligned
correctly.
Secure the cable (6) in place as directed by the eBike manu-
facturer (e.g. with cable clips).
Removing the PowerMore Battery (see figure C)
Firstly, disconnect the cable (6) by opening the cable lock as
directed by the eBike manufacturer.
Pull the release mechanism (14) towards you ❶ and remove
the cable connector (7) from the eBike charging socket ❷.
Press the release buttons (13) and remove the cable con-
nector (4) from the connection socket.
To remove the battery (1), press the release button (10)
and pull the battery (1) sideways out of the holder (9).
Note: As a result of varying designs, the PowerMore battery
may need to be inserted and removed using a different
method. Read the eBike manufacturer's operating instruc-
tions for how to do this.
Operation
Start-up
Note: The PowerMore battery can be used as the sole bat-
tery on the eBike. Please note that due to the reduced capa-
city, both the range and performance of the drive unit will be
reduced.
Switching on/off
Switching on the eBike battery is one way to switch on the
eBike. To do this, read and follow the instructions in the op-
erating manuals for the drive unit and operating unit.
Once the PowerMore battery is connected to the eBike via
the PowerMore cable, the eBike can be switched on/off via
the on/off button (5). Do not use any sharp or pointed ob-
jects to press the button.
To switch off the eBike battery, press the on/off button (5)
again. This will also switch the eBike off.
If no drive assistance is requested for about 10 minutes (e.g.
because the eBike is not moving) and no button is pressed
on the on-board computer or the operating unit of the eBike,
the eBike will switch off automatically.
The eBike battery is protected against deep discharge, over-
loading, overheating and short-circuiting by the "Battery
Management System (BMS)". In the event of danger, a pro-
tective circuit switches the eBike battery off automatically.
English – 3
If a fault is detected in the
eBike battery, two of the
LEDs on the battery charge
indicator (2) will flash. Con-
0 275 007 3RE | (10.02.2024)