METRO PROFESSIONAL GPH6000S Mode D'emploi page 12

NOTES:
• If the pilot light has not ignited, turn heater control knob to OFF position, fully close gas valve, wait 5 minutes, then repeat steps 2–4 of the Lighting
Instructions.
• If the pilot light ignites but does not stay lit, turn heater control knob to OFF position, fully close gas valve, wait 5 minutes, then repeat steps 2–3.
Now, using a lighter, ignite the pilot light through the ignition hole on the emitter screen. Once the pilot light is lit, press control knob for 30 seconds.
5. After pressing the control knob for 30 seconds, turn control knob to Low. To increase the temperature, turn towards Hi.
WARNING!
• Check that no broken on the glass is found before operation.
GB
• If a new gas bottle has been newly connected, let gas pipe air escape through ignition flame hole for at least one minute.
• When igniting the flame, ensure that the control knob is pressed the whole time while ignition button is pressed. The control knob can be released
once ignition flame is burning.
• You can observe and control the ignition flame through the little round window with sliding cover situated at the bottom of the radiation shade. The
ignition flame can also be lit with a match. Slide the sliding cover to the side in order to ignite the ignition flame with a match through the hole.
TO TURN OFF THE HEATER
1. Fully close gas valve on the gas cylinder.
2. Turn control knob clockwise to OFF position.
AFTER USE
CLEANING AND CARE
• Let the appliance cool down before cleaning.
• Wipe off powder coated surfaces with soft, moist rag. Do not clean heater with cleaners that are combustible or corrosive.
• Remove debris from the burner to keep it clean and safe for use.
• Cover the burner unit with the optional protective cover when the heater is not in use.
STORAGE
• Always close the gas value of the gas cylinder after use or in case of a disturbance.
• Remove the pressure regulator and the hose from the appliance.
• Check the tightness of the gas valve and other possible damage. If you suspect a damage, have the cylinder changed by your gas dealer.
• Never store liquid gas cylinder in a sub-terrain, or at places without adequate air ventilation.
DURING PERIODS OF EXTENDED INACTIVITY OR WHEN TRANSPORTING
• Turn the control to "OFF" position.
• Disconnect LPG cylinder and move to a secure, well-ventilated location outdoors. DO NOT store in a location that will exceed 50 °C.
• Store heater upright in an area sheltered away from weather conditions (such as rain, sleet, hail, snow).
• Cover heater to protect exterior surfaces and to help prevent dust and debris collecting in air passages.
WARNING!
• DO NOT touch or move heater for at least 45 minutes after use.
• Allow all burner elements to cool before touching.
NOTES:
• In a salt-air environment (such as near the sea) corrosion occurs more quickly than normal.
• Frequently check for corroded areas and repair them promptly.
• Wait until heater is cooled down before covering.
TROUBLESHOOTING
Suspected malfunctions, errors or damage are often due to causes that the users can fix themselves. Therefore, check the appliance using the below table before
contacting a qualified specialist. In most cases the problem can be solved quickly.
WARNING!
Only perform the steps described within this instruction manual! All further inspection, maintenance and repair work must be performed by an authorised
service centre or a similarly qualified specialist!
Problem
Pilot will not light
Pilot will not stay on
Burner will not light
In case of any faults or problems of assembly or use, please don't try to modify the appliance by yourself. Contact your supplier or distributor to solve it.
TECHNICAL DATA
CONSTRUCTION AND CHARACTERISTICS
• Transportable terrace/garden heater with gas cylinder housing.
• Casing in steel with powder-coating or in stainless steel.
• Gas hose connections with metal clamp . Heat emission from reflector.
Probable cause
• Gas valve is OFF
• Gas cylinder empty
• Opening blocked
• Air in supply system
• Loose connections
• Debris around pilot
• Loose connections
• Thermocouple bad
• Gas leak in line
• Gas pressure is low
• Gas pressure is low
• Opening blocked
• Control not ON
• Thermocouple bad
• Pilot light assembly bent
• Burner not in correct location
• Turn the gas valve ON
• Refill LPG tank
• Clean or replace opening
• Purge air from lines
• Check all fittings
• Clean dirty area
• Tighten connections
• Replace thermocouple
• Check connections
• Cylinder is empty. Refill it
• Cylinder is empty. Refill it
• Remove blockage and clean opening
• Turn the knob
• Replace the thermocouple
• Position correctly
• Position correctly and try again
12
Off: The heater stop working
Hi: Maximum temperature position
Lo: Minimum temperature position
HI
OFF
LO
Solution