Publicité
Les langues disponibles
Les langues disponibles
(fj)
REC RD LEVEL C NTR LS
To increase the recording levels, turn the knob to the right.
@REC INDICAT R
When your unit is recording, this indicator will light up red.
(]J)
l
W
BATTERY INDICAT R
When the batteries are exhausted, this indicator lights. When
the battery condition is satisfactory, this indicator remains
off.
(jj) MEM RY REW SWITCH (For Model PMD221)
When the tape is rewound with the MEM RY REW switch
set to
N, tape travel stops when the counter reaches "999".
(JJ)
PITCH C NTR L
When the PITCH control knob is at the "0" position, it is
set at normal speed. Turn it in the H direction to increase
the tape speed. Turn it in the L direction to decrease the tape
speed.
d 6)
vu
METER
The VU meter indicates the average recording/playback level.
(£7)
REC M DE SWITCH
MANUAL:
At this setting, the recording level can be
adjusted manually to your preference.
LIMITER:
At this setting, the transient high level input
signals are automatically decreased to a safe
recording level.
ALC:
At this setting, the recording level is automati
cally set to optimum level.
(jjj)
LEVEL C NTR L
The LEVEL control regulates the sound volume heard
through the speaker or headphone.
(j§)
PH NE JACK
Accepts headphones (optional) utilizing a standard stereo or
mono phone plug.
(^) MICR PH NE ATTENUAT R SWITCH
For extremely loud volume microphone recordings, depress
ing this switch prevents input overload and better record
level adjustment.
This switch also functions for direct telephone or built-in
microphone recording.
(^j)
MICR PH NE JACKS
Will accept any low impedance microphone (optional)
utilizing a 3.5 mm phone plug.
N TE:
When microphones are selected for recording do not monitor
through speakers as this will cause howling (acoustic feed
back) which could damage your audio equipment. Use head
phones for monitoring.
@LINE INPUT
Should be connected to the tape output jacks of your ampli
fier.
@) LINE
UTPUT
Should be connected to the tape monitor inputs of your
amplifier.
@ SPEAKER
N/ FF SWITCH (SPKR M N)
Place this switch in the
N position to monitor recordings
through the built-in speaker.
@ EXTERNAL DC P WER INPUT JACK (DC 4.5 V)
This jack is provided to operate your portable cassette
recorder from an external 4.5 volt DC power source.
(26) EXT SP JACK
Accesses the 3.5 mm plug of an external speaker.
INT NE C NTR L
Used to adjust the sound quality heard through the speaker,
headphone or direct telephone system. When the knob is
turned counterclockwise, the low frequency sound is de
creased. When the knob is turned clockwise, the high fre
quency sound is increased.
@) M NIT R SWITCH (For Model PMD221)
When recording, this switch may be placed in the S URCE
position to monitor the signal before it is recorded, or the
TAPE position to monitor the signal actually recorded on the
tape.
N TE:
When the M NIT R switch is set to S URCE, howling may
occur. At that time, lower the monitoring volume.
(^) TAPE SPEED SELECT R
STANDARD: The tape travels at normal speed: 1-7/8 ips
(4.75 cm/sec).
L W:
The tape travels are slower speed: 15/16 ips
(2.38 cm/sec).
(^(
remote jack
This jack accesses a 2.5 mm plug. With a microphone
equipped with a remote switch, playback or recording can be
stopped temporarily.
(^TELEPH NE PICK-UP JACK
This jack accesses the telephone pick-up for telephone
recording.
@ DIRECT TELEPH NE M DULAR JACK
With a telephone line connected to the direct telephone
modular jack, it is possible to record messages and play pre
recorded messages back through the telephone line.
@ANC SELECT R
Used to select flat (N RMAL), low cut ( /~ ) or high and
low cut ( r~ \ ) modes for a microphone, telephone pick-up or
direct telephone recording according to the signal condition.
(^) INPUT SELECT R
Used to select an input signal between LINE MIC/TEL
01
DIRECT TELEPH NE.
V
3
Publicité
