Publicité
Les langues disponibles
Les langues disponibles
DANGER
Disconnect power at supply line, circuit breaker or fuse before installing the
device.
NOTE
Do not place the device in a metal casing.
B
E
C
10
INSTALLATIEHANDLEIDING VOOR DE INSTALLATEUR
3
Open de klep op de basisplaat om de elektrische aansluitingen
zichtbaar te maken.
4
Verbind de 230V voedingsspanning met de connectoren.
5
Plaats het afdekkapje terug op de schakelaar.
Stap 3
Installation and Operation
MONTAGE Bewegingssensor PIR
instructions
Monteer de bewegingssensor steeds op een plaats waar beweging goed
kan gedetecteerd worden. Voorzie steeds een 230V voedingsspanning bij de
schakelaar.
VMI-02MP03
1
Demonteer de schakelaar.
2
Schroef de basisplaat (A) op de voorziene inbouwdoos met de
A
meegeleverde schroeven (F)
3
Verbindt de voedingskabel (230V) met de connectoren van de
5
B
bewegingssensor (B) door deze door het afwerkingspaneel (X) te steken.
4
C
4
Schroef de bewegingssensor (B) met de meegeleverde schroeven (E) vast
op de basisplaat (A).
3
5
Klik het afwerkingspaneel (C) op de bewegingssensor (B).
A: Status LED
B: Mode LEDs
A
F
1
About this manual
1.1 About the device
X
The VMI-02MP03 is a presence sensor for a ventilation system. The device
communicates information about presence via wireless communications with
the central control device.
1.2 How to use this manual
This manual is intended as a reference book by which qualified installers can
install the VMI-02MP03 (henceforth called "device") and users can use the device
for its intended purpose. Make sure you have read and understood the manual
before you install and/or use the device.
1.3 Original instructions
The original instructions for this manual have been written in English. Other
language versions of this manual are a translation of the original instructions.
1.4 Admonitions
NOTE
'Note' is used to highlight additional information.
2
Safety
2.1 Directives
ELEKTRISCHE AANSLUITING Bewegingssensor PIR
Hereby Honeywell declares that this VMI-02MP03 is in compliance with the
Op nevenstaand elektrisch schema staat de elektrische aansluiting
e
• EMC directive: 2014/30/EU
verduidelijkt. Beide aansluitingen (N&L) zijn vereist voor
• Low voltage directive: 2014/35/EU
• RED directive: 2014/53/EU
de basiswerking van de sensor. Er kan maximaal
• R0Hs directive: 2002/95/EC
• WEEE directive: 2002/96/EC
een lamp geschakeld worden van 20W.
2.2 Signs on the unit
CE marking of conformity
Dispose according to European Community
Directive 2002/96/EC (WEEE).
2.3 General safety instructions
The device is designed for indoor use only. Do not expose the device to rain or
moisture, to avoid short circuit. Short circuit may cause fire or electric shock haz-
ard. Operate the device between 0°C and 40°C. For cleaning of the device use a
soft damp cloth only. Never use any abrasive or chemical cleaner.
Do not paint the device.
3
Description
3.1 Intended use
The device is designed for following purposes:
1 Detect the presence of a person.
2 To switch a device, like a lamp, in case of presence.
Every other or further use is not in conformance with the intended use.
Stap 4
1
2
C: Touch Button
ro
N
N
L
Stap 5
3.2 Working principle
The device communicates with the control device using wireless communica-
tions in order to control the ventilation. The device switches on the light if it
detects movement. Movement in front of the device requests the high fan
speed and switches light on.
3.2.1 Light switch
The device detects movement in front of the device. If movement is detected,
it switches the lights on for the relay on time (ROT) and sets the ventilation to
high for a time, depending the ventilation unit.
4
Operation
4.1 Show status
1 Tap the button.
The Status LED shows the status of the system.
After 2 seconds the LED indicates detection of movement.
5
Installation
5.1 Preparation
DANGER
Disconnect power at supply line, circuit breaker or fuse before installing the
device.
NOTE
Do not place the device in a metal casing.
5.2 Installation procedure
X
B
E
C
N L
20W
Max
VMI-02MP03
H5V4 1823
T40
230VAC 50Hz 5mA IP21
: 230V switch, suitable for 20W resistive load.
Not all
have
A
F
N
N
L
else not
Publicité
