Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Fascia
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51165F
Wrenches: 3/4, 9/16, 10mm,
Drill Bits: None
Qty. (2)
½-13 Hex Bolt GR5
1
Qty. (2)
½ Conical Toothed Washer
2
Qty. (2)
½-13 Handle Nut
3
1.
Lower vehicle exhaust by removing tailpipe tangs out of rubber exhaust hanger at rear of vehicle.
2.
On the Passenger's side remove the (4) bolts that attach the exhaust heat
3.
On the Driver's side, remove the plastic rivet and nut that hold the plastic shroud to the frame rail. (Do not Discard).
4.
Raise hitch into position with frame bracket flanges between the frame rail and plastic shroud on the Driver's side and between
the frame rail and exhaust heat shield on the Passenger's side. Make sure that tailpipe tangs are above hitch bar while raising
hitch in to place. On some vehicles it may be necessary to remove chrome decorative ring off of end of tailpipe to allow muffler
to slide sideways toward middle of vehicle to allow better wrench access.
5.
Insert 1/2"-13 handle nuts through the large holes in vehicle frame rails and install fasteners as shown above.
6.
Insert the 3/8-16 U-bolt through the vehicle tow hook and insert through the mounting holes located on the hitch, (see above).
7.
Tighten all fasteners to the required torque specifications shown below.
8.
Reinstall exhaust heat shield over hitch Reattach exhaust to hanger & replace rivet and nut holding plastic shroud on
Driver's side. Heat shield may require trimming. Reattach chrome decorative ring to tailpipe if removed.
Tighten all 3/8 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009 Cequent Performance Products
Installation Instructions
Honda Civic
Including SI & Hybrid
Drawbar Kit:
3593
Drawbar must be used in the
Rise position only.
Frame Rail
Heat Shield
Tow Hook
3
2
1
4
5
Tighten all 1/2 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
2
3
Qty. (1)
3/8-16 U-Bolt GR2
Qty. (2)
3/8-16 Flanged Lock Nut
shield
to the vehicle. (Do not Discard).
51165N
Part Numbers:
51165
1
Exhaust
8-24-09
Rev. A
Publicité
Manuels Connexes pour Cequent Performance Products 51165
Sommaire des Matières pour Cequent Performance Products 51165
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 51165N 8-24-09 Rev. A 2009 Cequent Performance Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 51165N 8-24-09 Rev. A 2009 Cequent Performance Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Sheet 3 of 3 51165N 8-24-09 Rev. A 2009 Cequent Performance Products...