1. Manuels
  2. Marques
  3. Cequent Performance Products Manuels
  4. Accessoires de voiture
  5. 51146
  6. Instructions d'installation

Cequent Performance Products 51146 Instructions D'installation

Masquer les pouces
1
2
3
4
5
6

Publicité

Les langues disponibles

Les langues disponibles

Table des Matières

Frame Rail
Hitch Shown In Proper Position
Equipment Required: Torque Wrench
Fastener Kit: 51146F
Wrenches: 10mm, 17mm, 19mm
Drill Bits: NONE
Existing M12
Hex Washer Bolts
Both Sides
1
Qty. (4)
Conical Washer, 1/2"
2
Qty. (4)
Hex Bolt, M12 x 40 x 1.25
1.
CAUTION: SUPPORT THE BUMPER STRUCTURE TO KEEP IT FROM SWINGING OUT OF POSITION DURING HITCH
INSTALLATION.
2.
Referring to Figure 2, remove two (2) of the existing M12 hex washer bolts from the bumper bracket as shown, and loosen the
other three (3) bolts. Do this on both sides.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009 Cequent Performance Products
Installation Instructions
Toyota Tacoma
(Does Not Fit Toyota X-Runner)
Fascia
Existing Weld Nuts
Frame
Bumper
Structure
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3, PU4
5 Places
Both Sides
Figure 1
3
Qty. (4)
Spacer
Sheet 1 of 6
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
5500 (2497 Kg.)
5000 (2270 Kg.)
Bumper Bracket
Both Sides
Remove
Remove
Figure 2
51146N
8-3-09
51146
Max Tongue
WT (LB)
550 (250 Kg.)
500 (227 Kg.)
Loosen
Rev. A

Publicité

Table des Matières
loading

Manuels Connexes pour Cequent Performance Products 51146

Sommaire des Matières pour Cequent Performance Products 51146

  • Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 6 51146N 8-3-09 Rev. A 2009 Cequent Performance Products...

  • Page 2: Installation Instructions

    Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 2 of 6 51146N 8-3-09 Rev. A 2009 Cequent Performance Products...
  • Page 3 . Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 3 de 6 51146N 8-3-09 Rev. A 2009 Cequent Performance Products...

  • Page 4: Numéros Des Pièces

    . Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 4 de 6 51146N 8-3-09 Rev. A 2009 Cequent Performance Products...

  • Page 5: Números De Partes

    Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 5 de 6 51146N 8-3-09 Rev. A 2009 Cequent Performance Products...
  • Page 6 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 6 de 6 51146N 8-3-09 Rev. A 2009 Cequent Performance Products...

Table des Matières