Télécharger Imprimer la page

Solar-Shock SS-440 Manuel D'instructions page 3

Publicité

Les langues disponibles
  • FR

Les langues disponibles

ENGLISH
E. Reverse battery removal instructions when installing a replacement battery.
F. See battery enclosure cover for more instructions.
ELECTRIC FENCE INSTALLATION AND OPERATING TIPS
SUGGESTED ELECTRIC FENCE MATERIALS
POSTS
INSULATORS
Wood
Plastic
Steel
Porcelain
Aluminum
Fiberglass
SELECTING THE LOCATION FOR THE SOLAR SHOCK SYSTEM
Select a location that will allow the solar module to collect the maximum amount of sunlight
that is available on a clear day. An ideal location would allow the module to point directly at the
sun at noontime each day of the year. As a general rule, modules used in the northern hemi-
sphere should be faced due south (not magnetic south). Modules used in the southern hemi-
sphere should be faced due north (not magnetic north). The location site should be free of any
objects such as trees, that would block the sunlight from the solar module. See Illustration 1.
PROPER GROUNDING
Most fence problems are caused by poor grounding. Proper grounding is an absolute must if
your system is to work correctly. A ground rod should be copper, galvanized pipe or a steel rod driv-
en 6–8 feet (1.8–2.4 m) into permanently wet earth. The fence energizer will work more efficiently if
the ground rod is driven to a point where moisture is constant. Never use an existing ground rod that
is hooked up to other electrical systems or to a water pipe. To connect wire to a ground rod, use a
ground clamp that is mechanically secured to the ground rod. See Illustration 1.
TYPICAL ELECTRIC FENCE DESIGN
1. The design is simple and usually consists of wood, steel or aluminum posts fitted with Fi-
Shock insulators and threaded with a single strand of wire. (See Illustration 2). Spacing
between posts may vary at your discretion, but be sure the wire is always taut and never
allowed to sag excessively. Rule of thumb: space posts 12–25 feet (3.7–7.6 m) apart.
2. The earth is half your fence—so if your grounding rod is not satisfactory, you will have a poor
working fence. For best results, drive a 6-foot (1.8 m) steel rod, galvanized pipe or copper rod
into the earth. This grounding rod doesn't have to be next to the fencer, but can be located
nearby, preferably in a low, wet spot. This assures better grounding.
3. In dry or sandy soil areas it may be necessary to run a ground wire just below the "hot" wire.
This ensures proper "shock" if animal contacts both wires. In other words, some types of earth
4
WIRE
ACCESSORIES
Galvanized Steel
Gate Handle
Aluminum
Electric Fence Tester
Plastic-Metallic Wire
Lightning Arrestor
Ground Clamp
Electric Fence Sign
Ground Rod
do not conduct electricity well and often single-line fences do not work because of poor
grounding conditions. Check Illustration 3 for details.
FENCE WIRE RECOMMENDATIONS
Size: 20 through 9 American wire gauge (1–2.5 mm)
Type: 1. Smooth galvanized steel electric fence wire
2. Aluminum (conducts electricity 4 times better than steel).
3. Plastic/metallic wire (see wire manufacturer recommendation
located on the wire
package).
INSULATORS: See Figure A.
Use standard Fi-Shock insulators
on rod-type line support posts or
on wooden posts. At stress points
such as corners or the starting
point, use Fi-Shock corner post
insulators. Always insulate wood-
en posts. Do not staple wire
directly to the post or you may
have a problem with arcing.
SPLICES: Two types of splicing can be
used. One type in Figure A shows the use of
specially designed bolts that make splicing sim-
ple, fast and effective. The other type in Figure
B can be made without the use of extra materi-
als. Splice connectors may also be used.
INSULATED WIRE: 1. For running under
ENGLISH
5

Publicité

loading

Ce manuel est également adapté pour:

Ss-440-cSs-440-e