Troubleshooting - Hillyard T30 SC PRO Manuel D'utilisation Et D'entretien

MACHINE
TRIDENT
T30SC PRO
TRIDENT
T28SS PRO
This chapter lists the most common problems linked with the use of the machine. If you are unable to resolve the problems with the information
given here, please contact your nearest assistance centre.
PROBLEM
The main switch is set to "0".
Check that when switched on there
are no alarm messages on the
command display.
Make sure that the batteries are
THE MACHINE
correctly connected to each other
DOES NOT START
and that the battery connector is
connected to the electrical system
connector.
Check the charge level of the
batteries.
The plug on the battery charger's
cable is not correctly inserted into the
socket on the battery charger itself.
THE BATTERIES
The plug on the battery charger's
ARE NOT CHARGED
power cable is not correctly inserted
CORRECTLY
into the electrical outlet.
(VERSIONS
The characteristics of the mains
WITH AN ON
power supply do not correspond to
BOARD BATTERY
those required by the battery charger.
CHARGER)
The LEDs of the battery charger blink
repeatedly.
THE MACHINE HAS
Check the battery charge level, check
A VERY LOW WORK
the symbol on the command display.
AUTONOMY
The machine does not start.
THE MACHINE
DOES NOT MOVE
There is an issue on the drive pedal.
The quantity of detergent solution in
NOT ENOUGH
the water system is not sufficient for
DETERGENT
the work to be carried out.
SOLUTION ON THE
BRUSH
Detergent solution filter obstructed.
The machine does not start.
Not enough detergent solution comes
out.
The brushes have not been inserted
THE MACHINE
correctly in the machine.
DOES NOT CLEAN
CORRECTLY
The type of brush used is not suitable
for the dirt to be cleaned.
The brush bristles are excessively
worn.
CODE QTY BRISTLE
414272 2 PPL 0.3
414270 2 PPL 0.6
414273 2 PPL 0.9
414271 2 ABRASIVE
405508 2 -
449785 2 PPL 0.3
448012 2 PPL 0.6
448013 2 PPL 0.9
448014 2 ABRASIVE

TROUBLESHOOTING

POSSIBLE CAUSE
Make sure the main switch is on "I". If it isn't, turn the key clockwise.
Stop the machine immediately and contact the technician of the specialised
service centre, or press the SOS button if the HFM kit is installed.
Connect the batteries correctly inside the machine (see
BATTERIES IN THE
If the battery charge level is critical, perform a complete recharge cycle (see
paragraph
Reconnect the battery charger's power cable.
Check that the battery charger power supply cable plug is connected to the
mains socket.
Check that the characteristics in the battery charger plate are the same as
those of the mains supply.
Referring to the battery charger use and maintenance manual, check the
meaning of the flashing signals that the battery charger emits dung the
battery recharge stage.
If the battery charge level is critical, perform a complete recharge cycle (see
"RECHARGING THE
Read the section
Contact your nearest service centre.
Check that the amount of detergent solution present in the machine's water
system is sufficient for the work to be carried out.
Check the detergent solution filter isn't obstructed. If it is, clean it (see
"OCLEANING THE WATER SYSTEM
Read the section
Read the section
BRUSH".
Check that the disc brushes are correctly inserted into the machine (see
"ASSEMBLING THE BRUSH (SCRUBBING
THE BRUSH (SWEEPING
Make sure that the brushes fitted on the machine are suitable for the work to
be carried out. Read
Check the wear of the brush and if necessary replace it (see
THE BRUSH (SCRUBBING
(SWEEPING
NOTES
BLUE BRUSH
WHITE BRUSH
BLACK BRUSH
GREY BRUSH
PAD HOLDER
BLUE BRUSH
WHITE BRUSH
BLACK BRUSH
GREY BRUSH
SOLUTION
MACHINE").
CHARGING THE BATTERIES").
BATTERIES").
"THE MACHINE DOES NOT
FILTER").
"THE MACHINE DOES NOT
"NOT ENOUGH DETERGENT SOLUTION ON THE
VERSION)").
"CHOOSING AND USING THE
VERSION)" or
VERSION)").
31
INSERTING THE
START".
START".
VERSION)" or "ASSEMBLING
BRUSHES".
"REPLACING
"REPLACING THE BRUSH