EINHELL TE-MT 18/34 Li Mode D'emploi page 14

The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
4. Technical data
Motor power supply: ............................ 18V
Idling speed: ............................ 5000-34000 RPM
Clamping range .........................................
Max. attachments Ø: ..................................... 1-
Max. attachment length: ................................... ¾"
Max. spindle length: .......................................... 2"
Weight (Tool only): .....................................3.1 lbs
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Anl_TE_MT_18_34_Li_SPK7_USA.indb 14 Anl_TE_MT_18_34_Li_SPK7_USA.indb 14
EN
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).
5. Before starting the equipment
Warning!
Always remove the battery before making
adjustments to the machine.
5.1 Fitting the fl exible shaft (Fig. 1/Item 1)
Use the union nut (22) to screw the fl exible shaft
(1) onto the housing of the cordless rotary tool.
5.2 Wall-mounting (Fig. 3)
⁄ "- ⁄ "
1 1
32 8
You can fasten the machine on a wall using
⁄ "
1
4
the mounting holes (24) provided. The correct
dimensions for drilling holes in the wall can be
found on the back of the machine. (3-½ "/90 mm
and 6.65"/169 mm).
Spacing distances
≥ 4" from the wall (right + left)
≥ 40" from the ceiling
Important!
When mounting on a wall you must use suitable
screws (e.g. pan-head screws) in order to prevent
damage to the housing and risk of the machine
falling.
5.3 Shoulder strap (Fig. 3/Item 7)
The shoulder strap (7) can be used to carry the
machine, e.g. from your shoulder.
Fasten the shoulder strap (7) in the holes
provided using the two carabiners (23) as shown
in Fig. 3.
5.4 Storing the accessories (Fig. 5/Item 2)
The accessories can be stored in the storage box
(2). To access the accessories, pull the storage
box (2) out of the housing as shown in Fig. 5.
To quickly access frequently used accessories,
you can use the accessory rack (25) provided for
the purpose. See Fig. 5.
- 14 -
15.11.2023 10:22:15 15.11.2023 10:22:15