Publicité
Les langues disponibles
Les langues disponibles
Page 6 of
peu de superglue ou de la Loctite pour fixer l'écrou, car cela aider pour serrer
le côté oppose par la suite.
•
Passer l'axe de moyeu avec écrou et rondelle dans l'une des protections crash
(article 1) puis dans l'entretoise métallique (article 3) avec le diamètre le plus
large à l'intérieur de la protection crash.
Placer cet ensemble dans le moyeu de roue avant du côté droit de façon à ce
•
que l'axe dépasse de l'écrou de moyeu (article 4) et que l'entretoise se place
dans le moyeu de la roue.
Placer la protection crash restante (BO445M) sur l'extrémité de l'axe du côté
•
gauche.
Insérer la rondelle restante (article 6) et un écrou (article 5) du kit sur le
•
filetage dépassant de la protection crash.
•
Serrer chaque écrou des 2 côtés de façon identique puis veiller à ce que
l'insert plastique des 2 écrous soit complètement engagé et identique des 2
côtés.
Ne pas trop bloquer – les écrous fixent l'ensemble.
•
Vérifier que les protections fourche soient correctement serrées et fixées
•
fermement contre l'écrou de moyeu et l'entretoise, et ne tournent pas.
Après avoir utilisé la moto, vérifier le serrage des écrous régulièrement (par
•
exemple lors du nettoyage de la moto).
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G
may make design changes which do not diminish their performance or visual appeal and supplying them in
such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than
as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and
the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular
purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and
care and rectify any fault free of charge unless the workmanship has been disturbed.
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products.
On return of any defective Products R&G shall at its option either supply a replacement or refund the
purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect
arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for
causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its
liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned.
These terms do not affect the Buyer's statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be
returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise
to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All
returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing
price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued
products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not
refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007
ISSUE 1
15/03/2019 (DM)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com
Email:
9
FP0219
The Buyer is
info@rg-racing.com
Publicité
