Ryobi P505VN Manuel D'utilisation page 9

ADJUSTING BLADE DEPTH
See Figure 10, page 14.
Always keep correct blade depth setting. The correct blade
depth setting for all cuts should not exceed 1/4 in. below the
material being cut. More blade depth will increase the chance
of kickback and cause the cut to be rough. For more depth
of cut accuracy, a scale is located on the upper blade guard.
 Loosen the depth lock knob.
 Determine the desired depth of cut.
 Locate the depth of cut scale on the back of the upper
blade guard.
 Hold the base flat against the workpiece and raise or
lower the saw until the indicator mark on bracket aligns
with the notch on the blade guard.
 Tighten the depth lock knob securely.
OPERATING THE SAW
See Figures 11 - 13, page 14.
It is important to understand the correct method for operat-
ing the saw. Refer to the figures in this section to learn the
correct and incorrect ways for handling the saw.
WARNING:
To make sawing easier and safer, always maintain proper
control of the saw. Loss of control could cause an acci-
dent resulting in possible serious injury.
DANGER:
When lifting the saw from the workpiece, the blade is
exposed on the underside of the saw until the lower blade
guard closes. Make sure the lower blade guard is closed
before setting the saw down.
To make the best possible cut, follow these helpful hints.
 Hold the saw firmly with both hands.
 Avoid placing your hand on the workpiece while making
a cut.
 Support the workpiece so that the cut (kerf) is always to
your side.
 Support the workpiece near the cut.
 Clamp the workpiece securely so that the workpiece will
not move during the cut.
 Always place the saw on the workpiece that is supported,
not the "cut off" piece.
 Place the workpiece with the "good" side down.
 Draw a guideline along the desired line of cut before
beginning your cut.
OPERATION
CROSS CUTTING/RIP CUTTING
See Figure 14, page 15.
When making a cross cut or rip cut, align the line of cut with
the outer blade guide notch on the base.
Since blade thicknesses vary, always make a trial cut in scrap
material along a guideline to determine how much, if any,
you must offset the guideline to produce an accurate cut.
NOTE: The distance from the line of cut to the guideline is
the amount you should offset the guide.
RIP CUTTING
See Figure 15, page 15.
Use a guide when making long or wide rip cuts with the saw.
 Secure the workpiece.
 Clamp a straight edge to the workpiece using C-clamps.
 Saw along the straight edge to achieve a straight rip cut.
NOTE: Do not bind the blade in the cut.
WIDTH OF CUT SCALE
See Figure 16, page 15.
A width of cut scale has been provided on the base of the
saw. When making straight cross cuts or rip cuts, the scale
can be used to measure up to 4-1/2 in. on the right side of
the blade, and up to 1 in. on the left side of the blade.
BEVEL CUTTING
See Figures 17 - 18, page 15.
 Align the line of cut with the inner blade guide notch on
the base when making 45° bevel cuts.
 Make a trial cut in scrap material along a guideline to
determine how much you should offset the guideline on
the cutting material.
 Adjust the angle of the cut to any desired setting between
zero and 50°. Refer to Adjusting the Bevel Setting next.
ADJUSTING THE BEVEL SETTING
See Figure 18, page 15.
 Loosen the bevel lock knob.
 Raise the motor housing end of the saw until you reach
the desired angle setting on the bevel scale.
 Tighten the bevel lock knob securely.
WARNING:
Attempting a bevel cut without having the bevel lock knob
securely tightened can result in serious injury.
9 - English